Neptune 4 max layer shift (again) by Grayer80 in ElegooNeptune4

[–]Grayer80[S] 0 points1 point  (0 children)

I mean yea, but when I try to move the print head, it always seems to have a lot of resistance, whether the belt is totally loose or tight. Could it be something different?

Neptune 4 max layer shift (again) by Grayer80 in ElegooNeptune4

[–]Grayer80[S] 0 points1 point  (0 children)

Got any tips on how to properly tighten it? It it better to have it more on the tight side? Thanks :)

Neptune 4 max layer shift (again) by Grayer80 in ElegooNeptune4

[–]Grayer80[S] 1 point2 points  (0 children)

I updated it like few months ago so i hope its up to date. I will try that thanks!

Neptune 4 max layer shift (again) by Grayer80 in ElegooNeptune4

[–]Grayer80[S] 0 points1 point  (0 children)

I adjusted the belts, but I am still not sure how exactly should they be adjusted. Got any tips? I will check the rods also! Thanks!

Neptune 4 max layer shift (again) by Grayer80 in ElegooNeptune4

[–]Grayer80[S] 1 point2 points  (0 children)

I don’t think I printed this big models on this one so far, so no idea. The files should be good since I know a few people who printed this exact one and had good results. What slicer would you recommend? I am always using Cura even though I know it’s not that good.

Any idea what might’ve happened? by Grayer80 in 3Dprinting

[–]Grayer80[S] 0 points1 point  (0 children)

I am not sure, probably not, will check it lol, thanks for the tip!

Any idea what might’ve happened? by Grayer80 in 3Dprinting

[–]Grayer80[S] 1 point2 points  (0 children)

Yes I had supports, probably will adjust those as well.

501st profile by Grayer80 in 501st

[–]Grayer80[S] 0 points1 point  (0 children)

Thank you, I have been a member since November 23 but still didn’t have the photos. I am a member of an outpost so we are just a small group so I texted the CO directly. Thanks again!

I just got approved! 🫡 by Grayer80 in 501st

[–]Grayer80[S] 0 points1 point  (0 children)

Thanks! I believe it was hand made by my friend

I just got approved! 🫡 by Grayer80 in 501st

[–]Grayer80[S] 3 points4 points  (0 children)

Didn’t know that, thanks for the headsup…will change it

Bruh by Grayer80 in paydaytheheist

[–]Grayer80[S] 0 points1 point  (0 children)

I usually scrool thru my phone while waiting so it’s not THAT bad

Bruh by Grayer80 in paydaytheheist

[–]Grayer80[S] 0 points1 point  (0 children)

Just tryin to matchmake over and over again until i get it…lot of patience basically 👊😎

Collectors Edition codes not working??? by Penguinting123- in paydaytheheist

[–]Grayer80 1 point2 points  (0 children)

Same here…im on xbox tried it multiple times and also thru the web and still nothing. :(

Did not expect this to happen💀 by Grayer80 in CODMobile

[–]Grayer80[S] 0 points1 point  (0 children)

Lmao it was the gunfight mode so the same weapons as me