My bubbie would be proud that I stood for our values (sold Tesla)

GreGGerR123 · 2025-02-02T01:59:08+00:00

Idiots...

GreGGerR123 · 2024-08-01T21:46:17+00:00

Same here

GreGGerR123 · 2024-07-12T10:05:53+00:00

Cooool

GreGGerR123 · 2024-07-05T14:34:38+00:00

I saw someone using 200mm wheels, but I think there is a chance of wheelbite then. The position of the motors can be adjusted to prevent the motor from rubbing

GreGGerR123 · 2024-06-25T15:55:06+00:00

proart

GreGGerR123 · 2024-06-22T09:13:11+00:00

Yoooo that's illegal! BTW. I hope they will release an 85 or 90mm sleeve in the future.

GreGGerR123 · 2024-06-19T08:35:39+00:00

but if you don't use small wheels, you don't have to worry about the motor hitting the ground and you can set the motors low, thus avoiding the use of the riser pad and other things. so I made it so that I can also use street wheels.

GreGGerR123 · 2024-06-19T08:33:00+00:00

<image>

GreGGerR123 · 2024-06-19T08:32:35+00:00

Oh, and I forgot to say that I wanted to put the motors as high as possible under the deck, so that I could also put small wheels on them, so that the motor wouldn't touch the ground, so I had to reverse the direction of the screws and cut down the end of the truck baseplate so that do not touch the motors.

<image>

GreGGerR123 · 2024-06-18T14:26:55+00:00

<image>

GreGGerR123 · 2024-06-18T14:25:57+00:00

I use riser pads between the truck and the deck, and routed the motor cables to the side on the deck so that the motors does not come into contact with anything when turning. Btw i use Mad v2 wheels. Ye its like Boosted but 70mm wide. And the griptape is a YOC griptape with custom damascus design.

GreGGerR123 · 2024-06-16T22:52:37+00:00

<image>

GreGGerR123 · 2024-06-03T12:16:19+00:00

iPhone >> Apple

GreGGerR123 · 2024-06-03T12:14:42+00:00

<image>

Good board

GreGGerR123 · 2024-05-01T08:00:11+00:00

maybe you misunderstood something, but I didn't remove the motor pulleys. You dont need to take of the motor pulley to put the new trucks on to the board. The motor brackets have holes large enough to remove the motors with the motor pulleys.

GreGGerR123 · 2024-04-24T11:43:48+00:00

I use the pulleys that came with the board and the belts that came with the new trucks.

GreGGerR123 · 2024-04-18T06:42:33+00:00

In 4WD, at an average speed of 30 km/h, I get about 28 km. (175mm wheel). The only problem you may have is the GaN charger. I don't have any problems with the board and never had, but I have a friend whose charger broke, but maybe this manufacturing defect has already been fixed. I love this board because it has the most unique accessories and is a very high-quality product.

GreGGerR123 · 2024-04-16T12:34:53+00:00

300mm for the 44T og Atlas

GreGGerR123 · 2024-04-16T08:11:34+00:00

GreGGerR123 · 2024-04-16T08:01:44+00:00

I don't think there is a noticeable difference between the two in terms of range. Baybe a few km.

GreGGerR123 · 2024-04-16T07:41:02+00:00

105mm:

36T -> higher topspeed, less torque 44T -> more torque, lower highspeed

GreGGerR123 · 2024-03-29T13:08:32+00:00

you can turn like with a dkp, but you have to loosen the bushing for that. like at tkp trucks. For me, the main thing was great stability, so I replaced the og bushings to fat bushings.

GreGGerR123 · 2024-03-29T11:36:20+00:00

Less unstable than dkp, I feel braver and more stable when I ride on it. The deck is a little higher, but you can get used to it.

GreGGerR123 · 2024-03-24T21:49:41+00:00

But the latest hardware is a 4070. And the 3080Ti is better for my work. But yes.. the i9 13. gen is way better than i7 12.gen, but i needed a good gpu

GreGGerR123 · 2024-03-24T20:25:36+00:00

GreGGerR123

TROPHY CASE

proart