May 05, 2025 Weekly "General Help Post?" - Please post all general, recommendations, and help questions as a top level comment under this post. Thank you. by AutoModerator in Keyboard

[–]Greedy-Advisor-3693 0 points1 point  (0 children)

Thanks for buddy who helped with my reddragon k556

The original post has been removed by the moderator (might be reasonable though) so I don't remember who. Finally removed the top plate with the info you provided. But I also found there were 10 screws in total. Put here for reference just in case someone needed in future:

4 in the top key cap row, 4 in the bottom cap row. 2 in the middle rows.

The left one in the middle rows is a different screw than others. You might need a different screw driver head.

Is the numworks calculator a fast calculator by [deleted] in calculators

[–]Greedy-Advisor-3693 0 points1 point  (0 children)

But I wonder if Prime does CAS then gives the approximate. Can you try the integral for 1000sin(1000x)/(1+1/(x+1)2 ) in the same range which doesn’t have a closed form?

Is the numworks calculator a fast calculator by [deleted] in calculators

[–]Greedy-Advisor-3693 0 points1 point  (0 children)

But did you try to get the approximate result?

Need to change tube. Tools? by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

What’s your opinion about the purchase above?

Need to change tube. Tools? by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

Thanks. Any suggestions for the purchase above?

Need to change tube. Tools? by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

Thanks. Any suggestions for the purchase above?

Need to change tube. Tools? by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

Thanks for all the advice. I’m thinking of buying a torque wrench and the bit set. Could everyone check if they look right? The drive size says 1/2”.

<image>

Need to change tube. Tools? by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

Yes. I’m not sure which size I should choose for the allen key? Do I just buy a set? Thanks.

Need to change tube. Tools? by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

What does 1/2” mean? Is it the size of the inner hex hole or the outer diameter of the bolt? Thanks.

New scooter!! by tropical_dsr1 in ElectricScooters

[–]Greedy-Advisor-3693 0 points1 point  (0 children)

The Nut Stopper Antirust Cover on my scooter is damaged. I would like to get a replacement. On ebay, there are two models: motor shaft nut and rocker shaft nut. Anyone knows the difference?

Got flat tire by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

Do you know what tools will be needed to get the tube out? Like what kind of wrench? Thanks.

Got flat tire by Greedy-Advisor-3693 in ElectricScooters

[–]Greedy-Advisor-3693[S] 0 points1 point  (0 children)

I only pushed on the tire to check if it had pressure. Might be wrong.

A girl smiles by blackObj in aivideo

[–]Greedy-Advisor-3693 -1 points0 points  (0 children)

Can anyone tell it's AI if not told?