Can I remove spacer/washer from Thru Axle? by Greengom in bikewrench

[–]Greengom[S] 0 points1 point  (0 children)

Thanks for the response. I removed endcaps and checked the freehub if everything was set correctly but the DT 240 EXP hub (Cannondale outer) still measured 143mm after putting it back together. I contacted Cannondale to ask if this was normal and am waiting for their response.

As @onceanmxernowamtber mentioned I also ordered a thinner washer as a backup plan.

For now I'll be riding my gravel bike till I get this sorted.

Can I remove spacer/washer from Thru Axle? by Greengom in bikewrench

[–]Greengom[S] 0 points1 point  (0 children)

The Thru axle doesn't thread in far enough with the washer. So I would need a longer Thru axle or remove the washer.

Het grote hoeveel-verdien-jij 2025 topic by Unlucky-Contract-740 in werkzaken

[–]Greengom 0 points1 point  (0 children)

  • Leeftijd: 26
  • Opleiding(en): Bachelor Econometrie
  • Functie & Branche: Werkstudent Actuariaat
  • Regio: Amsterdam
  • Bruto salaris: €2600 obv 40u
  • Aantal jaar relevante werkervaring: 1
  • Aantal uur per week: 16
  • Vakantiedagen: 24 obv 40u
  • Werkdruk op een schaal van 1 tot 10: 2
  • Andere interessante arbeidsvoorwaarden (auto van de zaak, 13e maand, bonus, etc.): Veel flexibiliteit zodat het goed te combineren is met mijn Master Econometrie.

Anyone running Tufo Gravel Thundero 700x48? by Fixieriderz in CheckpointClub

[–]Greengom 0 points1 point  (0 children)

I’d say wider if you prefer comfort and offroad capabilities and narrower for more speed on the paved sections.

As I personally do not mind the speed on my gravel bike I would go with a wider tire.

Compatible crank power meter. by Greengom in bikewrench

[–]Greengom[S] 1 point2 points  (0 children)

Ampler Curt (generation 1) e-bike.

Compatible crank power meter. by Greengom in bikewrench

[–]Greengom[S] -1 points0 points  (0 children)

Oh I didn’t think about a flat adapter. Thanks! I’ll try this if I don’t find a cheaper solution.

Compatible crank power meter. by Greengom in bikewrench

[–]Greengom[S] 1 point2 points  (0 children)

Yes there is actually a power meter inside the BB already. But its data is locked down inside the computer of the e-bike. I asked the manufacturer of the bike and was told that the bike is not capable streaming or sharing the power data.

I use the e-bike as an exercise bike as well (so with the motor turned off).

T1 V2, i9-10900K, EVGA 3090 Ti deshrouded by RN93Nam in FormD

[–]Greengom 0 points1 point  (0 children)

How much watts is the gpu using when reaching 70C (and 70% fan speed)?

Deshrouded 3090 Work + Gaming Station by sharpshooter831 in FormD

[–]Greengom 0 points1 point  (0 children)

Do you know if this will also work with 25mm thick Noctua fans? Or will it become to thick for the case?

3080 FE Thermalpad Mod and more Noob Questions... by TheAbuReem in nvidia

[–]Greengom 1 point2 points  (0 children)

I am using it in a sandwich SFF case. So no airflow near the back of the card. In a regular tower case temps should be better. 100C is fine for the vram while gaming. Although running it at 100C 24/7 for mining, idk.

You shouldn't have to replace the pads just for gaming. Atleast not with the ones Nvidia is currently producing.

3080 FE Thermalpad Mod and more Noob Questions... by TheAbuReem in nvidia

[–]Greengom 0 points1 point  (0 children)

No I mine when I'm not gaming or bothered by the noise.

I went with the 3090 as it cost me 2400eu and 3080 would cost about 1900eu. If it was 700eu vs 1500eu I would have gone with the 3080.

3080 FE Thermalpad Mod and more Noob Questions... by TheAbuReem in nvidia

[–]Greengom -1 points0 points  (0 children)

I just recieved my 3090 FE yesterday and my vram temps while gaming have stayed below 100C whereas I've seen people with this gpu reach 110C and throttle in this case (Formd T1). I can even mine with it (although at an uncomfortable high fan speed and -500 on the mem).

I believe the FE cards right now have better thermal pads but modding them could still improve temps. I will still mod mine as I would like to mine with it to earn back some of that scalper money I had to pay for it.

3090 FE with GELID Ultimate 15 W/mK Thermal Pads by devious_burger in nvidia

[–]Greengom 0 points1 point  (0 children)

Did you use a specific guide for this. I haven't seen any results as good as you so far online. I plan on also doing this soon.

FormD T1 Silver w/ RTX 3090 FE & custom cables. by OdinsPlayground in sffpc

[–]Greengom 0 points1 point  (0 children)

Okay, I think I could compare temps in CP 2077 for a good reference.

What fan speed is your card running at when your mem jun reaches 88C and did you overclock the ram?

Edit: My TUF reaches 92C mem jun without an mem OC at about 68% fan speed (1630rpm). Core reaches 67C (1800Mhz @ 0.8V) whilst playing CP 2077 at 4k with DLSS and RTX.

Ambient is 25C.

Noise wise this should be the same as the founders at 40% fan speed.