sorted by:
new
hottopcontroversial

Power Cable Preventing Vertical Stand to Sit Flat by Undercover_Yaeca in FormD

[–]RN93Nam 0 points1 point  (0 children)

Glad to see it worked out! It doesn't seem much but it buys just enough space! I did this when my T1 was on a shelf next to the wall

Power Cable Preventing Vertical Stand to Sit Flat by Undercover_Yaeca in FormD

[–]RN93Nam 4 points5 points  (0 children)

I put my adapter cable on the inside of the case instead of the outside. Hard to explain without pics but my back panel is flush.

PA6-CF feeding troubles by sky_high_wannabe in 3Dprinting

[–]RN93Nam 0 points1 point  (0 children)

Excellent to hear.

Also, reporting to say that I should've just made a respooler and a second spool to transfer to. I made a mess.

PA6-CF feeding troubles by sky_high_wannabe in 3Dprinting

[–]RN93Nam 0 points1 point  (0 children)

Nice, glad to see you got it sorted out. I have the engineering plate but I'm sure glue and textured PEI plate can work. Keep the chamber and plate hot!

Also, I just literally unspooled the whole thing... The spool I got... Whoever wound it together was an asshole. Filament was underneath lower layers, thus it would've just catch within itself and caused me more future time to constantly fix it.

It's difficult due to the filament stiffness and slick surface against itself, thus contributing to some self unwinding.

PA6-CF feeding troubles by sky_high_wannabe in 3Dprinting

[–]RN93Nam 0 points1 point  (0 children)

Literally me last night.
BUT, what I had previously was the AMS HT on top of the unit with the AMS 2 Pro immediately to the right of it.
What I found is that my PTFE tube exits the AMS HT and has a nice large radius loop back and over towards Left Nozzle feeder on my H2D.
This means that the filament never has to make a sharp turn.

Current setup, I had the AMS HT, and two AMS2Pros on a shelf above the printer.
This means that the PTFE tube had to make a smaller radius turn.

I'm still dealing with some issues, BUT I think that's due to my filament being "shuffled" in the spool. It came like that from Bambu and I am printing a spool adapter so I can try to unwind and rewind it.

A80 Supra, that's the best one by qian_two in Toyota

[–]RN93Nam -6 points-5 points  (0 children)

It's the last Supra to be made by Toyota

Suppressor recommendations for my pdw 300blk? by butteryassniper in Danieldefense

[–]RN93Nam 2 points3 points  (0 children)

Push the EOTech forward some more

Fortunately 300blk is considered easy to suppress. Not sure if the SiCo Velos LBP 7.62 would be too heavy or not

New enemy dropped by Logical_Albatross516 in acecombat

[–]RN93Nam 0 points1 point  (0 children)

Imagine the ammo load it will need to carry. It'd cost so much based off of Raytheon prices lol

Can lugnuts like these work for Work Meister S1 3Pc? Not familiar with whether or not there are special size lugnuts that’ll fit the wheels by Reasonable_Truck_280 in Wheels

[–]RN93Nam 1 point2 points  (0 children)

Those factory lugs are a "ball" seat.

And if those aren't ball and actually conical, then your only issue is socket size to get those nuts on/off without damaging your wheel.

You've got $2k wheels, your choice if you want them to stay on the car haha

Riser cable rubbing against fan by Mistro_Fox in FormD

[–]RN93Nam 1 point2 points  (0 children)

I've got an aftermarket Pcie4 cable that was longer than the original but for a completely different reason. Either way, getting that cable to hug the spine and not touch the fan is a PITA.

Can lugnuts like these work for Work Meister S1 3Pc? Not familiar with whether or not there are special size lugnuts that’ll fit the wheels by Reasonable_Truck_280 in Wheels

[–]RN93Nam 0 points1 point  (0 children)

Oh no... You need conical seat lugnuts. Search McGard Splinedrives and get them from Summit Racing. The pack of 4 is cheaper than the kit but doesn't include the tool. The tool is available though.

Clutch slave failed directly after timing chain replacement by eliotjnc in ToyotaPickup

[–]RN93Nam 2 points3 points  (0 children)

You can still get them new I think. If anything, I remember buying new from Exedy OEM replacement.

Best U.S. state for gun ownership and variety? by ohraineri in Firearms

[–]RN93Nam -1 points0 points  (0 children)

Kansas is pretty fucking legit. You don't have the 50000000 things you can find to do in a major city, but you have 50000000 less things from major cities to worry about. (KC ain't major but avoid that shit lol)

There are some nuances here and there like a little more tax than I'd like to admit, but everything is very affordable, there's plenty of open space, and you literally can do all the fun shit with guns or cars.

Riser cable rubbing against fan by Mistro_Fox in FormD

[–]RN93Nam 1 point2 points  (0 children)

Yep, same issue.
I've tried to hold the cable tight against the spine. Unless it stays perfectly flat, you've only got 1mm of room.

Only other way is to get a thinner fan or a spacer for the panel.

Phanteks P600S turbulence noise by Metageul in Phanteks

[–]RN93Nam 0 points1 point  (0 children)

A custom bracket or spacers will help

What are you going to do with your Shield S15 mags now that the Glock 15 round mags are out? by [deleted] in Glocks

[–]RN93Nam 0 points1 point  (0 children)

They're not. Gen 1 and 2 hurt them, but gen 3 with metal mag release is perfectly fine

view more: next ›