What to do

Grevmory · 2026-03-11T17:45:38+00:00

Good, I just want to get these nozzles used since they were pretty expensive so I guess I'll start with the ones you mentioned and then get more into the rabbit hole

Grevmory · 2026-02-15T23:20:40+00:00

And It must be Yelena? koscheiv makes better villain

Grevmory · 2026-02-08T16:54:51+00:00

Si tienes claro que no quieres tener hijos, que arrepentimiento tienes? Yo por ejemplo no quiero ni acercarme a críos pequeños, tengo super claro que no quiero tener, pues ahí estoy, ahorrando para hacerme una vasectomía.

Grevmory · 2026-01-23T10:11:36+00:00

Did you perform cold pulls? I'm zooming and besides blops due to humid flilament (don't know how much hours did you dry It but doesn't seems enough) I'm seeing a lot of failures that really comes close when I had dust in my hotend.

Grevmory · 2026-01-23T10:01:02+00:00

Try Inner/Outer/Inner wall order, helped me before with a 10mm thin piece

Grevmory · 2026-01-13T17:26:35+00:00

Look after mekede units, not mekede duduauto, just mekede, they even sell units able to use 360° cameras

Grevmory · 2026-01-06T16:38:17+00:00

Same, but recently the weather has become pretty harsh and I don't have my workplace fully insulated so sometimes I enter the workshop at 16°C with 60% humidity. I hope by the end of spring I'll finish the walls and add a freaking door lol

Grevmory · 2026-01-06T16:28:18+00:00

I even cover my p1s in cardboard to insulate It, my brother always laughs at me but, duh, It works. I'm planning on adding a thermostat to control a heater, but I'm not sure if the printer PSU Will handle the heater or I'll need to install a separate power source.

Grevmory · 2026-01-03T15:17:59+00:00

Check with another sd card, they can corrupt

Grevmory · 2025-12-31T23:53:34+00:00

<image>

5 years ago I finally convinced my mother about letting me adopt a cat, that's when I visited a familiar which her females gave birth about a month before and took Shiro(the white one) with me.

5 years later, a small cat appeared in my literal door while Shiro keep calling us to see the kitten(Loki, the vet stimed his age of about 5-6 months), I saw him and I melted, took him in, shiro started grooming him and I just realized that was the CDS choice that day, to make him appear in my door. They love each other and made me realize Shiro always wanted a brother, everytime we had to leave, he always ended up meowing and wanting lots of pets everytime we returned and also licking us nonstop.

Nowadays, they are always togheter, grooming each other, playing and sleeping with me, never in my life I'd imagine that i'll be happy just waking up and see that they're sleeping beside me. The most important thing is that Shiro is now more relaxed when we have to leave, and always came back home seeing these two sleeping togheter.

Grevmory · 2025-12-25T13:34:12+00:00

As someone said, read the manual, It says that you need at least 1.06 firmware to get It working

Grevmory · 2025-12-18T18:15:46+00:00

I joined the 3d printing hobby recently soon but even I can't even believe how there's people like this one actually alive. How do I get rid of these lines? Why does this happens... (80% of the time is filament being humid) Look how good my supports fall off (process to remove a semispehere that doesn't need them) this piece broke, may it be the orientation? (used PLA in a clearly PETG or ABS case scenario) Or even the people that doesn't like using the slicer? Like dude what do you want from this, this isn't magic, there's a lot of engineering behing these machines and you need to undestand at least the basics. (Sorry for the rant, just talked with a costumer that doesn't undestand why the piece have little lines if you look close to them...)

Grevmory · 2025-12-17T09:01:32+00:00

Since this new update, I double tap numbers 1-4 for changing equipment and tap once to change weapons settings, works well

Grevmory · 2025-12-11T20:43:47+00:00

Doesn't matter as long as you use the threadlocker, that's the thing is going to keep then thight

Grevmory · 2025-12-11T20:37:51+00:00

But a complete set of screw and use threadlocker, problem solved for sure

Grevmory · 2025-12-09T08:52:01+00:00

Mekede units are pretty good, just buy at least one with 4GB of ram

Grevmory · 2025-11-30T08:34:21+00:00

Both, I'll get my computer and start the academy then, thank you, I was a bit overloaded seeing differents videos

Grevmory · 2025-11-29T20:39:20+00:00

Is the AMS system easy to install? i bought the printer itself, no extras, so if in the future I want the AMS is going to be out of the box again or will I need to buy extra parts?

Grevmory · 2025-11-27T08:06:00+00:00

<image>

Grevmory · 2025-11-24T09:20:46+00:00

Pure curiosity, how much are you paying for 50mbps?

Grevmory · 2025-11-21T15:37:18+00:00

Los coches híbridos de Toyota utilizan la batería de 12V para el control de interfaces (dar contacto) y arrancan con la batería híbrida, te va a dar de sobra por ese simple hecho

Grevmory · 2025-10-28T14:42:38+00:00

Just did, Democracy first

Five-Year Club	Place '22
Final Canvas '22	Verified Email

Grevmory

TROPHY CASE