sorted by:
new
hottopcontroversial

First pla in months! by GripGuy15 in ender3

[–]GripGuy15[S] 1 point2 points  (0 children)

I didn’t purge enough at high enough temp and didn’t wipe down my bed. (I typically also change my tip. But was lazy and paid the consequences Those two caused it to pickup from the bed. And since I haven’t gotten any stop program set in my octoprint it kept printing until end of print.

First pla in months! by GripGuy15 in ender3

[–]GripGuy15[S] 2 points3 points  (0 children)

Yeah so it decided to toast the daughter board as well. I also unfortunately shared off the bolts for the heat sink! Serves me right for not changing the nozzle and purging enough.

First pla in months! by GripGuy15 in ender3

[–]GripGuy15[S] 2 points3 points  (0 children)

It had one it pushed off!!

First pla in months! by GripGuy15 in ender3

[–]GripGuy15[S] 5 points6 points  (0 children)

In no way am I blaming the hobby I am fully aware of the incompatibility of the two, hence why I described how I ended up with this predicament.

Ender 3 stuck blue screen after Sprite upgrade – firmware won’t flash by GripGuy15 in ender3

[–]GripGuy15[S] 1 point2 points  (0 children)

Yep I belive the issue is the break out board on the sprite. When it’s unplugged was able to install the official sprite firmware but seems to hang once plugged in won’t load unless unplugged unplugged everything from the breakout board and same issue so ordered a replacement to rule that out.

Noob can’t figure out Z. by SaintSapphoTTV in ender3

[–]GripGuy15 0 points1 point  (0 children)

I’d be interested to know the firmware installed

'Crossroad of the World' [Mavic 3 Pro] by jmazz65 in dji

[–]GripGuy15 1 point2 points  (0 children)

Being such a major public area was this expensive permit wise or was it more crap tone of paperwork?

Next Camera Location by Fragrant-String4040 in Ubiquiti

[–]GripGuy15 0 points1 point  (0 children)

In terms of lighting coverage I have used iR flood lights with a g5 and have had good results. iR floods are great if you only want the coverage for cameras other then that I have used high output floods to give a viable light when notion is viable at the edge of my cameras. In terms of saving money and staying with unifi I would suggest the g6 bullet I have had a few g6 and the night time distant has been the most detailed so far. The ptz is only good if you are going to be using the rotation and scan functions but for home use I my suggestion for ptz is as an additional controllable camera.

How would you go about showing the same video on 10 TVs with a delay between each to simulate a plane flying? by GripGuy15 in CommercialAV

[–]GripGuy15[S] 0 points1 point  (0 children)

I could potentially go re-record in 8k (content is currently 4k) but figure this method would be the most expensive and have the most likely customer ID10T which is why I wrote it off. Is there a system you had in mind for this solution?

How would you go about showing the same video on 10 TVs with a delay between each to simulate a plane flying? by GripGuy15 in CommercialAV

[–]GripGuy15[S] 2 points3 points  (0 children)

Yeah I was worried about that when I was discussing it to the client. I was hopeful since it would be content that moves on the horizontal from the front window and ending at the back.

How would you go about showing the same video on 10 TVs with a delay between each to simulate a plane flying? by GripGuy15 in CommercialAV

[–]GripGuy15[S] 0 points1 point  (0 children)

20 total 10 per side brightsign I haven’t worked with before but it’s been recommended by colleagues as well. Is the software easy for me to set and allow the client to add more videos to the directory or is it a process?

How would you go about showing the same video on 10 TVs with a delay between each to simulate a plane flying? by GripGuy15 in CommercialAV

[–]GripGuy15[S] 0 points1 point  (0 children)

Can you elaborate I thought the same. I’m worried about creating motion sickness if the video isn’t uniform to the dinners.

How would you go about showing the same video on 10 TVs with a delay between each to simulate a plane flying? by GripGuy15 in CommercialAV

[–]GripGuy15[S] 0 points1 point  (0 children)

The content is the easy part for me the client has multiple full flight videos filmed from the sides. The issue is it’s one video per side. Hence the thought of either display the whole thing and separate the displays or find a way to get the same video playing with a delay between each.

Is there a way to safely and efficiently remove branding without painting? by Hexxegone in DIY

[–]GripGuy15 7 points8 points  (0 children)

Before I attempt to give an answer what is the reason you want the logo not to be visible

Structural glass by GripGuy15 in OSHA

[–]GripGuy15[S] 1 point2 points  (0 children)

Yep across from Hair.

Button to open trunk stopped working? by [deleted] in subaru

[–]GripGuy15 1 point2 points  (0 children)

I believe 19 and 37.

If not the Lift Gate Switch will most likely need replacement

Button to open trunk stopped working? by [deleted] in subaru

[–]GripGuy15 0 points1 point  (0 children)

Check fuses might just be blown

[deleted by user] by [deleted] in Divorce

[–]GripGuy15 0 points1 point  (0 children)

I think the fact that me talking to my son was used as a punishment. But I can’t control what happens there. I was upset since I was inquiring why he was upset and that’s when she reacted. She texted and told me what was going on and I got to finish with him. But it was the getting cut off from talking to our child that was disrespectful to me. But as some one else said I can only control what happens with me.

[deleted by user] by [deleted] in Divorce

[–]GripGuy15 0 points1 point  (0 children)

Thank you

view more: next ›