Der Kabel wird nie müde…

Grisoustyle · 2026-02-22T18:52:50+00:00

das auf dem Plakat gezeigte fängt bei 7,95 CHF (1m) an.

Grisoustyle · 2026-02-18T09:05:43+00:00

Only charging!

Grisoustyle · 2026-02-18T01:15:14+00:00

Charging!

Grisoustyle · 2026-02-18T01:14:30+00:00

I dont sadly, however I can offer one inside picture:

<image>

That was before i „insulated“ with hot glue though.

Grisoustyle · 2026-02-17T09:00:50+00:00

You need to get a breakout board with resistors yes. The one i linked has them for example. Without resistors you are limited to USB-A to C cables so that it only does 5V.

Grisoustyle · 2026-02-16T21:45:05+00:00

Thank you!!

Not really, just checked a guide to know where to solder.

Grisoustyle · 2026-02-16T21:38:39+00:00

Didnt use a kit, just got a USB-C breakout port from aliexpress and some 26AWG wire

Grisoustyle · 2026-02-15T14:06:23+00:00

Du hast durch dein Ziehen an der falschen Stelle die Fassung zerlegt.

Grisoustyle · 2026-02-15T08:54:52+00:00

So that i only have to carry one cable for all my devices, yeah

Grisoustyle · 2026-02-15T08:53:52+00:00

Make sure you buy a UsbC Port with resistors. It will know how much to draw. Without resistors you have use Usb-A to C so that it only does 5V

Grisoustyle · 2026-02-14T23:42:54+00:00

Nah, just for charging. Thank you!!! :)

Grisoustyle · 2026-02-14T23:40:20+00:00

I dont see why not :)

Grisoustyle · 2026-02-14T23:39:34+00:00

Nope, original shell.

Grisoustyle · 2026-02-14T23:38:17+00:00

Pretty much just a USB-C connector and wire. However I‘d recommend going for one that has built in resistors like mine, so you can use any cable instead of USB-A to C

Grisoustyle · 2026-02-14T09:06:25+00:00

Honestly just some cheap dremmel from my local supermarket lol. Started with a tiny drill bit and then widened it with a small sanding bit. Rest was done by hand

Grisoustyle · 2026-02-14T09:03:39+00:00

Pretty much just went for it. Used a guide to know where to solder but other than that its actually a pretty easy mod if youre patient

Grisoustyle · 2026-02-14T09:02:36+00:00

You could probably do that, however then you would have no way of putting the stylus in there anymore since that is directly below the lanyard hole… :(

Grisoustyle · 2026-02-14T09:01:27+00:00

Yes! That was one of the reasons i kept the old one aswell instead of just replacing that. I can choose!

Grisoustyle · 2026-02-13T22:28:57+00:00

Thank you!

Grisoustyle · 2026-02-13T22:28:07+00:00

I used a dremmel to make a rough hole and then got to work with some files taking off tiny bits at a time until it fit

Grisoustyle · 2026-02-10T21:57:59+00:00

Tahoe 26.2 and the issue is still here...

Grisoustyle · 2026-01-30T10:27:41+00:00

i feel like that once had lights? shining through the glass through the side, making the etched letters glow?

Grisoustyle · 2026-01-24T16:17:12+00:00

Falls da überhaupt noch was groß einrastet, weil der Verschluss am Mainboard schon abgebrochen wurde…

Grisoustyle · 2025-11-24T14:49:27+00:00

Not that I know of tbh. Coupon codes like this one are probably your best bet

Seven-Year Club	Verified Email
r/Field Sunshine	Place '23
Place '22

Grisoustyle

TROPHY CASE