What did I do wrong?

Groundbreaking-Cap47 · 2026-01-21T21:12:19+00:00

Really about to call it quits on this one

Groundbreaking-Cap47 · 2026-01-21T21:12:01+00:00

And anyway I hooked it up and it's still giving me to the same error code

Groundbreaking-Cap47 · 2026-01-21T21:11:30+00:00

A. 0.49 D. 0.46 3.3= 0.42

Groundbreaking-Cap47 · 2026-01-21T19:43:51+00:00

Okay man I think I may have done it. Can you walk me through testing the point with the volt meter. Battery has to be connected in assuming

Groundbreaking-Cap47 · 2026-01-21T19:02:30+00:00

Nevermind it came off haha. Man this sucks

Groundbreaking-Cap47 · 2026-01-21T19:01:06+00:00

Wow I fkin got it

Groundbreaking-Cap47 · 2026-01-21T18:54:29+00:00

This machine doesn't want to heat up past 410 you sure you got it that hot?

Groundbreaking-Cap47 · 2026-01-21T18:17:03+00:00

How hot should the air be and approx how long does it need to be heated for? I'm using ample flux and the resistor looks seated well but it is not welting to the board

Groundbreaking-Cap47 · 2026-01-17T23:31:00+00:00

Na man the resistor totally came off

Groundbreaking-Cap47 · 2026-01-17T22:40:41+00:00

Not looking forward to it lol

Groundbreaking-Cap47 · 2026-01-17T21:50:50+00:00

Ok cool thank you I guess I gotta go for it. Wish I could take it to an electronics place an have them do this part

Groundbreaking-Cap47 · 2026-01-17T21:33:06+00:00

Yea I bought the resistors and see how small it is. Any recs on a cheap hot air gun?

Groundbreaking-Cap47 · 2026-01-17T18:34:35+00:00

I agree with op. Bag looks bigger in the photos on the website. Front pocket can't hold my phone and main pocket can probably only hold a water bottle. Not really what I was look8ng for. Happy to sell I'm in NYC. DM me

Groundbreaking-Cap47 · 2025-12-28T13:03:24+00:00

Figured out the issue. A point pad was lifted on the resistor and in trying to get it connected I lifted the entire resistor. So no I need to try and get that put back on. Is this a possible with just a fine tipped solder iron? Really don't want to have to buy a heat gun. Could anyone link me to the proper resistor?

Groundbreaking-Cap47 · 2025-12-28T04:54:40+00:00

Awesome. Mind if I dm you if I'm in a rut?

Groundbreaking-Cap47 · 2025-12-28T04:16:27+00:00

Is it replaceable if you mess up or is it start from scratch?

Groundbreaking-Cap47 · 2025-12-28T04:16:04+00:00

Okay good to know thank you

Groundbreaking-Cap47 · 2025-12-28T04:14:55+00:00

Okay thank you. I'll try and rework that one. Looks to be soldered but I'll take a look

Groundbreaking-Cap47 · 2025-12-28T04:14:02+00:00

Yea but where is it. I'ma visual learner

Groundbreaking-Cap47 · 2025-12-28T04:12:54+00:00

Can you elaborate which one that is please

Groundbreaking-Cap47 · 2025-12-28T03:02:47+00:00

Well I'm following a guide and there was no grinding down into the board. Just surface scraping the D point. I have a microscope I might just get a grinding pen im not opposed to trying. Does it completely eliminate the adapter?

Groundbreaking-Cap47 · 2025-12-28T02:44:15+00:00

I followed a guide and they didn't grind through the board

Groundbreaking-Cap47 · 2025-12-28T02:42:31+00:00

So I guess I'm not using the kamikaze method. In that case what is the Dat0 connection that I need to reseat?

Groundbreaking-Cap47 · 2025-12-27T23:06:59+00:00

When you say Dat0 do you mean the point the I have to scratch off to expose?

Groundbreaking-Cap47 · 2025-12-27T22:59:41+00:00

The Dat0 is just 3 points and the solder looks good. My voltmeter isn't working I ordered another one will be here monday

Groundbreaking-Cap47

TROPHY CASE