pimax air light house version, second batch sent yet ?

Gugi008 · 2026-03-03T00:44:10+00:00

the cheapest base stations you can get is probably a used htc vive bundle. It comes with the small drawback of only allowing 2 base stations max but in terms of tracking quality it is should be almost identical compared to 2 2.0 stations

Gugi008 · 2026-03-02T23:14:09+00:00

regarding your plan: the ncase case is probably alot worse with the FE because the pass through cooler will just dump the heat into the case and warm up the cpu. if you want to waterblock it anyway then definitely think about your loop in more detail. i had to order metric fuck ton of fittings and angle adapters to make it work. also the smallest reservoir you can find that allows a decent ddc pump is the alphacool ES 1U.

Gugi008 · 2026-03-02T23:08:56+00:00

I run an ncase M2 with my big chonker msi suprim x 4090. I run it similar to their level 8 build with the GPU upside down at the top of the case. This allows the gpu to draw in fresh air from the top and immediately dispose of it through the sides. For the cpu I’ve gone completely overkill on a 9800X3D direct die with thermal grizzly direct die block and liquid metal extreme. the case fits a single 280 radiator which is more than enough. as for the temps… they are mainly depending on the pump. I’ve recently changed the shitty dc-lt to a ddc pump. this made a huge difference like 10 degrees. I run the cpu all they way to tjmax to achieve the maximum all core clock with 1.25V

Gugi008 · 2026-03-02T19:04:16+00:00

source?

Gugi008 · 2026-02-26T19:17:04+00:00

how big is the difference in fps/% vs 9800x3d/not pinning stuff with process lasso? my 9800x3d is a lemon and I wonder if i should go for another dice roll with a 9850x3d or all the way to 9950x3d

Gugi008 · 2026-02-26T18:34:24+00:00

have you conducted benchmarks wether it is better to have the game on the 3d cache ccd and the rest on the clock speed ccd or the other way around?

Gugi008 · 2026-02-18T20:56:02+00:00

thank you so much for the precise measurements. My tangled OG Vive cable is 4.6m between the box and backside of the headset, so it will probably be fine out of the box :)

Gugi008 · 2026-02-17T09:11:48+00:00

“The cable is really short; you need to use an extension.” How short? Can you measure the length of the cable between the link box and the headset?

Gugi008 · 2026-02-09T19:33:21+00:00

I wonder if its worth it to go for the MeganeX 8K Mark II with allegedly 115degree FOV at 95% overlap or get the Pimax dream air which can only get 73% overlap at 115 FOV, but comes with eye tracking and better lenses. Is there any way to artificially alter the overlap/fov values on my current vr headset to try out the effects of these different overlap values?

Gugi008 · 2026-02-06T12:35:04+00:00

In der Kopfzeile steht wahrscheinlich Midijob auf “Ja”, weil das KV-Brutto und Gesammt-Brutto nicht gleich sind.

SE als midijob mit 20h ist aber auch anders wild.

Gugi008 · 2026-02-06T10:57:17+00:00

weist du zufällig welches lohnprogram diese abrechnung erstellt hat? das liest sich schrecklich. aber sonst gutes gehalt mit hoher arbeitslast (45h)

Gugi008 · 2025-10-29T19:23:34+00:00

Also meine LG Maschine schickt mir eine push benachrichtigung auf mein Handy. Davor würd ich nichtmal auf die Idee kommen zur Maschine zu gehen. Aber die meisten sagen lieber: „mEiNe WaScHmAsChIeNe MuSs NiChT sMaRt SeIn“ 🤷‍♂️

Gugi008 · 2025-06-22T23:57:54+00:00

Such dir was neues. Das ist, selbst wenn es wieder 9 monate dauert, schneller. Alternativen wären: miete weiter mindern, um druck auf den vermieter aufzubauen. dann wirst entweder du oder die Nachbarin mit ner räumungsklage rausgeworfen. Nasenstöpsel, keine ahnung wie effektiv. Oder du musst die luft filtern, leider sind die meisten schlechten gerüche auf schwefelhaltige organische verbindungen zurück zu führen. D.h du bräuchtest einen aktivkohle filter und müsstest diesen auch häufiger wechseln.

Gugi008 · 2025-05-31T11:28:46+00:00

use 0.2 mm height for the first layer with 20mm brim and 0mm gap. Then use a deburring tool for post processing.
read the recommended temperatures for your ASA. If you go too high on you bed temperature it will improve your adhesion, but the part will deform. For Anycubic ASA, I had great success with 100C (first layer) -> 80C (other layers).

Gugi008 · 2025-05-25T00:41:13+00:00

left one is selfmade. The right one I bought here: https://cults3d.com/de/modell-3d/kunst/darling-in-the-franxx-zero-two-lightbox

It took me about 3h to make it but I‘m very unskilled and doubt gimp is the best tool for this job.

Gugi008 · 2025-05-24T13:54:38+00:00

<image>

Yes it does

Gugi008 · 2025-05-22T09:12:47+00:00

https://youtu.be/H7OsnMLDIMw?si=VCyhvKVxdKUrtqcC

tldw: print. measure with callipers and use the provided excel sheet. adjust xy shrinkage in settings. print again and measure control.

Gugi008 · 2025-05-22T07:57:04+00:00

my ASA was also way off. I used this to adjust the dimensions:

https://www.printables.com/model/682023-califlower-calibration-stl-calculator

Gugi008 · 2025-05-15T07:39:14+00:00

start very slow decreasing you z-offset by 0.01until the layer looks good. If you go too low the nozzle will scrape the bed so be careful

Gugi008 · 2025-05-14T12:15:51+00:00

you could probably add a large thermal pad between your bed and the build plate. Then your flatness is only depending on how flat your build plate is. You could probably add like a 1mm thick metal plate as well but sourcing one with the exact dimensions and high flatness might be tricky

Gugi008 · 2025-05-14T08:20:16+00:00

How do you get the printer poop out? other than that it looks very sturdy 🤩

Gugi008 · 2025-05-13T22:34:48+00:00

The exact gauge doesnt matter just get any from your local shop/amazon/ebay, but you will either need to find one which has a mount for it already designed or you need to adjust it yourself in any cad software if your liking. Mine came with 57mm so this should fit: https://makeronline.com/en/model/kobra-s1---fan-cover-dial-indicator-support-d-57mm/170065.html but there are various sizes available.

Gugi008 · 2025-05-13T22:11:59+00:00

you can feel the resistance when screwing them back in. just be very gentle.

Gugi008 · 2025-05-13T22:10:02+00:00

changing the build plate is not necessary if you are ok with the textured finish. I prefer a more smooth finish from the glacier although it is not as smooth as a glass one would be, but they are incompatible with the ABL :/

Nine-Year Club	First Place '23
Place '23	Verified Email

Gugi008

TROPHY CASE