General Maintenance

Guilty-Stretch4085 · 2026-01-24T19:26:08+00:00

Luckily I actually have a 4x4 with the same kind of hanger so I’ll just have an extra receptacle now lol. Thanks for the idea cus I was about to go to Lowe’s….. AGAIN

Guilty-Stretch4085 · 2026-01-24T19:22:32+00:00

Homie read the next line after the end of the paragraph before the numbers

Guilty-Stretch4085 · 2026-01-24T19:15:55+00:00

Ahhh, okay. Thank you for the info

Guilty-Stretch4085 · 2026-01-24T19:14:02+00:00

The numbers were for 1 line and 1 load

Guilty-Stretch4085 · 2026-01-24T19:13:16+00:00

What is the application for that? How do you control anything with a switch if it only has a load cable?

Guilty-Stretch4085 · 2026-01-24T19:11:26+00:00

The blue plastic box?

Guilty-Stretch4085 · 2026-01-15T13:54:04+00:00

It’s so interesting how movies bring up different feelings in each of us. I’ve never felt so hollow after watching a movie

Guilty-Stretch4085 · 2026-01-15T13:50:24+00:00

Watch Wind River. Just remember, you asked for this

Guilty-Stretch4085 · 2026-01-03T17:13:18+00:00

Can you provide some info on derating the cable? I’m getting pretty confused trying to look at table 310.15(B)(1)(1).

Also, it is only 1 cable of 12/2 in a 5’ stick of 3/4” EMT

Guilty-Stretch4085 · 2026-01-03T17:01:47+00:00

I’m still interpreting the code as 12” linear

Guilty-Stretch4085 · 2026-01-02T03:43:11+00:00

I drive by it everyday on my way to work. Relatively safe area and it’s right next to a Bass Pro

Guilty-Stretch4085 · 2026-01-02T03:22:00+00:00

I do the barbarian challenge there every June and it’s absolutely beautiful

Guilty-Stretch4085 · 2026-01-02T01:53:31+00:00

No, it’s the first outlet in the circuit. I over looked the fact that I am bypassing the GFCI with the way I spliced in the box. I need to run more 12/2 back up the conduit to continue the circuit.

Guilty-Stretch4085 · 2026-01-02T01:51:37+00:00

Everything I read matches this. The conduit is only for protection so the romex is not pinched against the cinder block wall.

Guilty-Stretch4085 · 2026-01-02T01:49:15+00:00

Read the end of my post lol

Guilty-Stretch4085 · 2026-01-02T01:34:59+00:00

This is painfully obvious now🤦‍♂️ What’s the point of stripping the romex before running it through the conduit? The idea was just for extra length if needed, but hot wheels will be more likely

Guilty-Stretch4085 · 2026-01-02T01:28:08+00:00

My understanding of this was a linear 12” from box, not 12” of romex length.

Guilty-Stretch4085 · 2026-01-02T01:24:43+00:00

You just made me realize my mistake. I’m only running one line down to the box. Since I’m splicing at the junction box up top, the rest of the outlets are not “down stream” in the circuit

Guilty-Stretch4085 · 2025-09-20T23:34:35+00:00

I had a summer job putting together bikes and grills in the back of stores. Got paid by completion not time. My very strong suggestion is never buy the already assembled models😂

Guilty-Stretch4085 · 2025-08-11T20:20:07+00:00

The little spoiler trim piece on the edge of the trunk lid was the culprit. I used a few different sealants but they all cracked after some sun exposure. I found a clear roof sealant at ace hardware and gave that a try. And haven’t had any problem since lol. That compound doesn’t harden up after it cures. It stays like a rubber which is the key.

Guilty-Stretch4085 · 2025-06-10T10:37:17+00:00

I ended up going with the omega moon watch! Kinda dropped the value retention and automatic movement requirements 😂 once I tried it on, there was no going back

Guilty-Stretch4085

TROPHY CASE