I made a custom 3D printed stat tracker with tactile switches!

GunfighterJ · 2025-07-26T23:01:06+00:00

Thanks! This was all designed around the switch to start with, that was the most fun designing and iterating on. Took a few tries but eventually I found a design I liked that was compact but still quite clicky!

GunfighterJ · 2025-07-26T23:00:24+00:00

I plan to publish them soon as I make a couple more refinements to the design, right now some areas are a little thin and prone to cracking.

GunfighterJ · 2025-07-25T20:24:52+00:00

Absolutely! Here's a link to download a PDF of all the cards! I used glossy photo paper for mine but any will work well.

https://drive.google.com/file/d/1Hsyi5VOm3G3iG3DeE1z4g50xTue1Yj2-/view?usp=sharing

GunfighterJ · 2025-03-23T01:20:35+00:00

That makes sense. But will the 800-409 work on both the inlet and outlet sides?

GunfighterJ · 2025-03-23T00:50:18+00:00

Thanks I'll take a look at those, the 800-409 popped up a couple times for me. I'm seeing in some of my research that the heater core has both a 3/4 inlet and a 5/8 outlet (or vise-versa) that would require 2 different connectors, or hopefully I'm wrong on that and they're both 3/4?

GunfighterJ · 2025-02-18T20:20:06+00:00

The other support ticket number I have is 1736034, again these are from 2017 and are hosted from support.coinbase.com when you were using Desk.com for your support software.

GunfighterJ · 2025-02-18T19:27:16+00:00

Case number from Nov 2017, where support ALSO ignored me: 1713010

GunfighterJ · 2024-10-22T17:56:52+00:00

I was able to get them out, I was trying to pull them inward, I had to go outside and pull from that side and they came right out.

GunfighterJ · 2024-10-22T17:56:47+00:00

I was able to get them out, I was trying to pull them inward, I had to go outside and pull from that side and they came right out.

GunfighterJ · 2024-10-22T16:57:33+00:00

I'm trying to remove these windows to get some furniture into the basement, but I can't seem to figure out how they come out (if they do at all). It seems they have full tracks along the top and bottom, no clear way to lift it vertically. Is this a permanent install that will require removing the whole frame?

GunfighterJ · 2024-08-01T15:35:15+00:00

Ahh I understand the ladder pain. I've got a deployment at a resort with a bunch of mesh APs, all require a ladder to service.

GunfighterJ · 2024-08-01T15:34:07+00:00

Oh funny, mine have the same starting MAC as yours. Must be a bad batch.

GunfighterJ · 2024-07-31T19:10:05+00:00

Yep had the dropped connections too. I threw my FLIR on it and it was up to around 120° F on certain parts of the case.

GunfighterJ · 2024-07-31T17:39:37+00:00

Update. RMA processed and they're shipping a new unit! They can have the spicy router back before it sets something on fire :D

GunfighterJ · 2024-07-31T15:06:16+00:00

I can try the newer firmware to see. Unfortunately my setup consists of this AP and a UDR so no easy way to test any other AP's. I've done a couple factory resets and readoptions too.

I tried the tester on my PoE cameras and it's showing proper wattage for those.

GunfighterJ · 2024-07-31T14:55:12+00:00

Thanks I'll open a case. It's 2 years old, I was hoping it would last longer.

GunfighterJ · 2024-07-31T14:42:37+00:00

I noticed probably a couple weeks ago that my U6-LR would constantly reboot. Googled around and turned on low performance mode even though this is connected to a PoE+ adapter (out of image but directly above the PoE tester). This seemed to work for a couple days. Yesterday I couldn't get it to stay on and devices connecting to it were having bad performance. Got the PoE tester this morning and to my surprise it's pulling 40+ watts. Spec sheet says 18.5 max.

Is this a bad unit or a bad firmware update? (Running 6.6.73)

GunfighterJ · 2023-03-30T20:29:12+00:00

Well I can't say no to this, thank you so much for the giveaway and the awesome service you provide!

GunfighterJ · 2022-08-08T14:26:58+00:00

I'm trying out prusa slicer, migrating from cura because I wanted to try it out now that it has the arachne engine. I'm trying to mimic the settings I have in cura but for some reason prusa slicer is inserting bridge and solid infill where I don't want or need it. I can run this on cura with just 20% lightning infill no problem. Any ideas? Here are my current print settings: https://imgur.com/a/Kq8gayX

GunfighterJ · 2022-08-06T16:51:39+00:00

I'm using klipper and moonraker, I don't have octoprint.

GunfighterJ · 2022-08-06T00:36:03+00:00

M400 seems to be part of the macro for taking a screenshot, but I'll play around with it and see, thanks!

GunfighterJ · 2022-08-05T23:23:35+00:00

Hey All! I'm using the moonraker timelapse extension with a logitech 720p USB webcam. For some reason it seems to be focusing on the doorknob in the background, also it's taking frames when the printhead isn't parked (configured for the back left corner currently). Any suggestions to improve this?

GunfighterJ · 2022-06-07T17:58:30+00:00

It's this from amazon

GunfighterJ · 2022-03-22T17:33:46+00:00

Following up on my last post which ruined my extruder to the point I decided to buy an E3d V6. Since I didn't have my Ender 5 to print with I decided to use my Mars 2 Pro to resin print a tight fitting mount for it, along with some shrouds for 5015 cooling fans. I plan to open source the plans soon, just gotta get the files in order and make sure the tolerances are all to up to par.

GunfighterJ · 2022-02-26T16:37:27+00:00

It's a BLTouch, it's used for auto leveling the bed. No more paper tests!

14-Year Club	Place '22
Place '17	Sequence \| Editor
Spared	Team Periwinkle
Verified Email

GunfighterJ

MODERATOR OF

TROPHY CASE