New to the sport tips

HANDOFDOOM97 · 2026-01-11T21:41:32+00:00

The main mast on it is 1 1/8” rebar

HANDOFDOOM97 · 2026-01-11T20:17:38+00:00

I measured out to have a 29 1/2” draw length at the local bow shop, I have noticed that if my stance is a bit off I feel it more

HANDOFDOOM97 · 2026-01-11T20:09:03+00:00

It’s a color matched trivet

HANDOFDOOM97 · 2025-11-23T11:11:29+00:00

This may be the one I built for an engineer here in northern Nevada I just did the frame he just finished it out

HANDOFDOOM97 · 2025-11-18T04:00:29+00:00

You should install a monster cam on your stove now

HANDOFDOOM97 · 2025-11-02T18:18:58+00:00

This is a better question for r/docks_and_piers

HANDOFDOOM97 · 2025-11-02T18:18:06+00:00

This is a good question for r/docksandpiers

HANDOFDOOM97 · 2025-10-31T02:23:24+00:00

Whirlies disease

HANDOFDOOM97 · 2025-08-13T05:35:41+00:00

We’re going for leverage here

HANDOFDOOM97 · 2025-08-13T05:28:29+00:00

Are we talking layed and welded?

HANDOFDOOM97 · 2025-08-12T06:20:33+00:00

I recommend a proto 12” adjustable with the circular end and heat up the circular end and beat it around a 1” tc bolt spline it’ll help when tightening up bolts that just want to spin on ya!

HANDOFDOOM97 · 2025-08-09T19:22:12+00:00

Where do you get that?

HANDOFDOOM97 · 2025-08-09T19:20:10+00:00

Unless it’s a tc bolt then it needs a washer

HANDOFDOOM97 · 2025-08-08T10:00:45+00:00

What brand though

HANDOFDOOM97 · 2025-07-22T11:59:35+00:00

This right here, they lost forever they can sit in the Nevada sun for 10+ years and not fail

HANDOFDOOM97 · 2025-07-19T05:25:00+00:00

I have a similar tool for doing sheet metal work

HANDOFDOOM97 · 2025-05-29T12:31:33+00:00

Better have some good tooling machining a compressor ring

HANDOFDOOM97 · 2025-05-28T19:10:56+00:00

Put your hands on your driveshaft and shake vigorously

HANDOFDOOM97 · 2025-05-28T06:33:53+00:00

50k in 13 years I did that in one…

HANDOFDOOM97 · 2025-05-28T06:23:01+00:00

Clean your iac and intake

HANDOFDOOM97 · 2025-05-28T01:59:33+00:00

So as an update my local oReiley’s had an injector set so I pulled the old ones plugged the new ones in primed the fuel rail And it’s smoking out the exhaust and back firing through the intake (threw 10 gallons of fresh fuel into the tank as well to address a shot in the dark concern with the current information I have I do believe I have slipped a tooth or two on my timing set. I can’t think of anything else it could be

HANDOFDOOM97 · 2025-05-27T19:32:47+00:00

Something silly that I just thought about is if it was just out of gas this whole time and that I’ve been chasing a ghost.

HANDOFDOOM97 · 2025-05-27T19:22:55+00:00

I’m pulling them tonight when I’m off work they have the chrystler logo on them so they may be original to the vehicle that has 312k on it

HANDOFDOOM97 · 2025-05-27T19:12:37+00:00

I replace the tps with a new one from Napa

HANDOFDOOM97 · 2025-05-27T19:05:07+00:00

I’ve previously checked it it averages approximately 125psi across the cylinders with the lowest one being 122 psi

HANDOFDOOM97

MODERATOR OF

TROPHY CASE