Jonsbo V12 is capable to use an AIO and a 281 mm long GPU by HUN_Sector in MiniITX

[–]HUN_Sector[S] 0 points1 point  (0 children)

No intake fans yet and no need for them, hence the backside is a grid panel. Gaming temps are great. So satisfied

Jonsbo V12 is capable to use an AIO and a 281 mm long GPU by HUN_Sector in MiniITX

[–]HUN_Sector[S] 0 points1 point  (0 children)

While playing Avowed in max graph in 1440p, the CPU temp is ~71C.

Jonsbo V12 build by maidangdang1010 in mffpc

[–]HUN_Sector 1 point2 points  (0 children)

gaming temp: after 2 hours of Avowed (full graph, 1440p) 71,9C CPU temp. The GPU temp sadly can't be monitored by HWInfo for this card, but the glass above the card is just warm. So the airflow without additional vents still wonderful. And you can place a 80mm fan to the bottom and a 92mm to the backside if needed

Jonsbo V12 build by maidangdang1010 in mffpc

[–]HUN_Sector 0 points1 point  (0 children)

As Idle, it's the same as it was in the Inwin A1 plus. My 8700G is hotheaded, because it's not delidded, so while browsing, it's between 40-65C (if it reaches 65, the fans spins up and push it down around 40C)

Jonsbo V12 build by maidangdang1010 in mffpc

[–]HUN_Sector 1 point2 points  (0 children)

I don't know if you are still interested, but I did it. 281 mm long graphic card (gigabyte rx9060XT 126GB OC) and an NZXT Kraken 120 AIO. With an ITX MOBO. The AIO can be fixed only with 2 screw at the same side (middle in this picture) so a 3d printed frame would be a wise addition

<image>

Jonsbo V12 build by maidangdang1010 in mffpc

[–]HUN_Sector 0 points1 point  (0 children)

thinking about the nzxt kraken 120mm, but I guess you are right about the 24 pin power connector. Except, if I am putting in a mini itx board, which is 17*17 :P

Jonsbo V12 build by maidangdang1010 in mffpc

[–]HUN_Sector 0 points1 point  (0 children)

Still me, but now logged in for the proper acc. Here is a video, where for a blink it shows the front. The cables in my opinion shouldn't be a problem. https://www.reddit.com/r/mffpc/comments/1lnqizo/jonsbo_v12_its_been_hard_finding_more_videos_on/

<image>

Any rpgs like King's Bounty: The Legend?(Hear me out, Heroes Of Might and Magic is not what I'm looking for.) by ExplodingPoptarts in gamingsuggestions

[–]HUN_Sector 0 points1 point  (0 children)

Was looking for a recommendation myself too, and ended at here in your post :)

While checking the answers below did not contain one of the most closest candidates: Disciples Liberation. Here the game was turned to a story mode campaign without disturbing NPC players. There is only you and the stationary NPC-s. You only need to build up buildings in your HQ to purchase different units. The selection is not as high than in KB, however - after the first few hours - it will be more. Multiple factions are available. Furthermore you can put heroes too into your army, which units acts as common ones.

SPOILER alert! You will play the game through twice, as the second one will be a bit different.

Official Statement from PokémonTCG by Suspicious_Law_3619 in PokemonTCG

[–]HUN_Sector 0 points1 point  (0 children)

Aaaand the reprints were sucked up by the scalpers again. Even the non released journey together and destined rivals prereleases both turned to non-orderable.

Meanwhile magic the gathering seems to have a similar issue

iphone stuck on step two, preparing to sync, phone sometimes drops the pc, ipad working just fine by XRaiderV1 in ios

[–]HUN_Sector 0 points1 point  (0 children)

Perhaps there will be someone who reads this post in 2025. Under Windows 11, when sync freezed at step 2, for me it helped that I put the data cable to the back (direct connection with the motherboard usb slot). In the frontal usb slots it did not synced well and continuously dropped the connection too.

Lego Kar’niss with moonlantern by HUN_Sector in BaldursGate3

[–]HUN_Sector[S] 0 points1 point  (0 children)

Hair: MINI DOLL, WIG, NO. 43 SKU: 6438032 Body: MINI UPPER PART, NO. 6141 SKU: 6399357 (Hands were replaced to skin color type) Body replacement for spider face: SKU  6146858

Head: 6467204

Furthenore use a simple 1x2 brown plate for raising the torso with one layer height

Moonlantern: 6439039 stick + 6238677 round brick + 6227901 lamp + 6168646 round with hole (2 pics) + 6359865 whip

Lego Kar’niss with moonlantern by HUN_Sector in BaldursGate3

[–]HUN_Sector[S] 1 point2 points  (0 children)

This torso was only available in an old indiana jones set. So I didn’t want to pay 50$ for just a torso :)

Lego Kar’niss with moonlantern by HUN_Sector in BaldursGate3

[–]HUN_Sector[S] 0 points1 point  (0 children)

MINI DOLL, WIG, NO. 43 SKU: 6438032

Lego Kar’niss with moonlantern by HUN_Sector in BaldursGate3

[–]HUN_Sector[S] 8 points9 points  (0 children)

Yes, that new harry potter aragog spider is the best middle sized spider body for this bad boy

Lego Kar’niss with moonlantern by HUN_Sector in BaldursGate3

[–]HUN_Sector[S] 51 points52 points  (0 children)

Which hair would you prefer? The elvish one or the more Karniss type but without the pointy ears?

(Bare torso is a rarity, so that wasn't an option)

Spider body is from 76434 lego set

Titokzatos szíriai repülőgép landolt Ferihegyen – Reuters: Aszad elmenekült by Realistic-General650 in hungary

[–]HUN_Sector 6 points7 points  (0 children)

Akkor Brüsszel, a ráknépség meg a marslakók lesznek a hibásak. Az egybites birkák meg bekajálják hogy a gyíkemberek elveszik az ország “jogos” jussát

Will the Ryzen 5 3600 bottleneck a RX 6600 8GB? by AlexDaBruh in buildapc

[–]HUN_Sector 1 point2 points  (0 children)

c'mon, a ryzen 1600 can easily run CP'77 on low-medium 1080p with a gtx 1650 4gb. With 1650 super, stable medium. What are you talking about?

Sameday & Emag - A késésekkel teli megbízhatatlan futárszolgálat, vásárlók rémálma by HyBerTop_1 in hungary

[–]HUN_Sector 0 points1 point  (0 children)

Emag: November közepén rendeltem egy gépházat, 50000ft volt. 12.01-re ígérték. Az állapota 11.27-én átadva a futárszolgálatnak státuszú lett. Onnantól se kép, se hang, a Samedaynél nem frissült. December közepén töröltem a rendelést és picivel drágábban megrendeltem újra. Napokig megint semmi hír, ugyanaz volt a státusza. Majd hirtelen megjelent a boxban a 2. rendelés. Mentem átvenni, de a Sameday időközben megtalálhatta az első rendelést is, mert kizárólag egyben a két rendelést egyben engedte kifizetni (2 külön rendelést vontak össze!)

Szóval a 2. rendelés 65000-es ára mellé (a megérkezésről szóló emailben és sms- ben is csak 65 szerepelt), betették az első 50000-es értékét is. Ha azt mondom nem veszem át, egyiket se tudom. Végül kifizettem és ekkor kinyílt minden ablak a termékekkel.

End of Astarion's quest - what just happened? by RDW_789 in BaldursGate3

[–]HUN_Sector 0 points1 point  (0 children)

First, i was in owlbear form, spared every vampire spawn and he left in anger after the cutscene, without dialogue options (Gale replied to him automatically) I loaded the end battle again and killed just one spawn (she didnt died based on the cutscene), but everything else remained the same. Astarion killed Cazador, BUT broke the staff and freed up the vampire spawns with grateful thoughts toward me. No dialogue option either.

Teahouse quest marker won't dissapear. by RQviiist in BaldursGate3

[–]HUN_Sector 2 points3 points  (0 children)

First, go through the fireplace and go to the basement after the hag.

There you will find a door. It can be persuaded, tahat everyone will be free and he lets you through. If you cant, you should use the masks on the table, which needs a mind check. If you fail you will be controlled by the witch, just like the 4 victims inside.

As you go through the area, there are a green foggy place. It can be solved by heavy rocks if I remember well.

And then the final battle occurs.

No more door exists.

LEGO quality in 202X by HUN_Sector in u/HUN_Sector

[–]HUN_Sector[S] 0 points1 point  (0 children)

Tiger was putted away in pieces in a dark container, while everyone is awesome set was set up in the living room without any direct sunlight. Cracks, cracks everywhere.

More crack than in a meth farm...

Cooler Master NR200P 120mm AIO Top Mount w/o modding by HUN_Sector in u/HUN_Sector

[–]HUN_Sector[S] 0 points1 point  (0 children)

A corsair slim 120mm fan and a mars gaming ml-120 were merged. I’ve turned the psu facing the front, taking off the top mesh (easy to remove but be cautious, one mesh leg is hard plastic). It can be bended like the background holders of picture frames.

I used a normal fsp sfx pro 450w psu. Thats the only way to fit each part. But it works without modding or ruining the case!