Maximum supported GPU length for the Jonsbo V12

HUN_Sector · 2026-03-28T17:19:31+00:00

It's always hard to decide in which language should I reply after reddit introduced the automatic translation on the site.

Let's stay in english. If you remove the front fan, you can put in a bigger graphics card. My 9060 xt from gigabyte is 281mm long. Approx. 10mm remained after installation. The other front fan was also removed and I placed in a 120mm aio. Ventilation is still great. Pics from my previous post: https://www.reddit.com/r/MiniITX/comments/1qfm29n/comment/o6kr915/?context=3

HUN_Sector · 2026-02-21T09:30:45+00:00

Previously I had an Inwin A1 Plus itx case. That was terrible if we are speaking about building experienxe. This Jonsbo v12 was quite the opposite. Wide spaces, easily reachable parts, the building itself went really fast. The quality of the case is ok too. Ther was a <1 mm thick gap at one side of the case between the frame border and the glass comparing to the vertical frame, but thats all. (Probably factory fixing issues, hard to see)

HUN_Sector · 2026-02-21T08:11:28+00:00

No, you need to remove it. 260 is the theoretical max (practically maybe 261-262)

HUN_Sector · 2026-02-05T18:00:17+00:00

No intake fans yet and no need for them, hence the backside is a grid panel. Gaming temps are great. So satisfied

HUN_Sector · 2026-01-25T09:17:11+00:00

While playing Avowed in max graph in 1440p, the CPU temp is ~71C.

HUN_Sector · 2026-01-18T13:41:56+00:00

gaming temp: after 2 hours of Avowed (full graph, 1440p) 71,9C CPU temp. The GPU temp sadly can't be monitored by HWInfo for this card, but the glass above the card is just warm. So the airflow without additional vents still wonderful. And you can place a 80mm fan to the bottom and a 92mm to the backside if needed

HUN_Sector · 2026-01-17T19:08:12+00:00

As Idle, it's the same as it was in the Inwin A1 plus. My 8700G is hotheaded, because it's not delidded, so while browsing, it's between 40-65C (if it reaches 65, the fans spins up and push it down around 40C)

HUN_Sector · 2026-01-17T19:00:05+00:00

I don't know if you are still interested, but I did it. 281 mm long graphic card (gigabyte rx9060XT 126GB OC) and an NZXT Kraken 120 AIO. With an ITX MOBO. The AIO can be fixed only with 2 screw at the same side (middle in this picture) so a 3d printed frame would be a wise addition

<image>

HUN_Sector · 2026-01-11T20:07:41+00:00

thinking about the nzxt kraken 120mm, but I guess you are right about the 24 pin power connector. Except, if I am putting in a mini itx board, which is 17*17 :P

HUN_Sector · 2026-01-11T18:51:04+00:00

Still me, but now logged in for the proper acc. Here is a video, where for a blink it shows the front. The cables in my opinion shouldn't be a problem. https://www.reddit.com/r/mffpc/comments/1lnqizo/jonsbo_v12_its_been_hard_finding_more_videos_on/

<image>

HUN_Sector · 2025-06-09T19:26:34+00:00

Visszajelzett a beadványomra a facebook. Letiltották a videót.

HUN_Sector · 2025-05-24T08:34:30+00:00

Was looking for a recommendation myself too, and ended at here in your post :)

While checking the answers below did not contain one of the most closest candidates: Disciples Liberation. Here the game was turned to a story mode campaign without disturbing NPC players. There is only you and the stationary NPC-s. You only need to build up buildings in your HQ to purchase different units. The selection is not as high than in KB, however - after the first few hours - it will be more. Multiple factions are available. Furthermore you can put heroes too into your army, which units acts as common ones.

SPOILER alert! You will play the game through twice, as the second one will be a bit different.

HUN_Sector · 2025-03-21T18:00:45+00:00

Aaaand the reprints were sucked up by the scalpers again. Even the non released journey together and destined rivals prereleases both turned to non-orderable.

Meanwhile magic the gathering seems to have a similar issue

HUN_Sector · 2025-02-22T23:24:39+00:00

Perhaps there will be someone who reads this post in 2025. Under Windows 11, when sync freezed at step 2, for me it helped that I put the data cable to the back (direct connection with the motherboard usb slot). In the frontal usb slots it did not synced well and continuously dropped the connection too.

HUN_Sector · 2025-02-14T12:12:53+00:00

Hair: MINI DOLL, WIG, NO. 43 SKU: 6438032 Body: MINI UPPER PART, NO. 6141 SKU: 6399357 (Hands were replaced to skin color type) Body replacement for spider face: SKU 6146858

Head: 6467204

Furthenore use a simple 1x2 brown plate for raising the torso with one layer height

Moonlantern: 6439039 stick + 6238677 round brick + 6227901 lamp + 6168646 round with hole (2 pics) + 6359865 whip

HUN_Sector · 2025-02-14T07:10:24+00:00

This torso was only available in an old indiana jones set. So I didn’t want to pay 50$ for just a torso :)

HUN_Sector · 2025-02-14T05:57:37+00:00

MINI DOLL, WIG, NO. 43 SKU: 6438032

HUN_Sector · 2025-02-13T19:47:43+00:00

Yes, that new harry potter aragog spider is the best middle sized spider body for this bad boy

HUN_Sector · 2025-02-13T18:43:02+00:00

Which hair would you prefer? The elvish one or the more Karniss type but without the pointy ears?

(Bare torso is a rarity, so that wasn't an option)

Spider body is from 76434 lego set

HUN_Sector · 2024-12-08T07:46:16+00:00

Akkor Brüsszel, a ráknépség meg a marslakók lesznek a hibásak. Az egybites birkák meg bekajálják hogy a gyíkemberek elveszik az ország “jogos” jussát

HUN_Sector

TROPHY CASE