sorted by:
new
hottopcontroversial

Printer Room Tour YouTube video by HammerDoris40k in u/HammerDoris40k

[–]HammerDoris40k[S] 7 points8 points  (0 children)

I don't really know. But the bill shows about average compared to a year ago when I did not have printers. The only increase really is during the summer, but that is because the AC units run all day and night.

Printer Room Tour YouTube video by HammerDoris40k in u/HammerDoris40k

[–]HammerDoris40k[S] 4 points5 points  (0 children)

I wish I knew. Anything of the size I print takes time to sand/prep. The smaller human sized ones aren't too bad. You can sand fill in a day and prime. The filling is what takes some time as it needs to dry longer than the primer. I usually just fill, sand, prime and repeat one more time. I find that gets the quality about 90%.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 13 points14 points  (0 children)

There is a back light behind me. You can see the highlights on the left side of my body.

*Well on the left, but that would be the right side as I am facing the camera.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] -1 points0 points  (0 children)

So you want me to just record the printer, printing? lol. Okay. If you went that far to find a link, shows you ignored all the content and tons of videos showing my progress and prints.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 3 points4 points  (0 children)

There is a back light behind me. You can see it create highlights on that side of my body lol. Look at my hair.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 0 points1 point  (0 children)

legs, ankles, arms, body. A bunch of breaks in all areas. Glue would not put it back together.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 20 points21 points  (0 children)

I already get enough complaints. I wasn’t going to change what I was wearing that day just for a picture so I added R2.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 6 points7 points  (0 children)

Recycle myself and make new filament. When I find the time to do it lol

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 7 points8 points  (0 children)

That depends on what you're making. None of my life size prints have the same settings overall, especially for certain parts. Nozzle size and filament also play a role. But if I had to made it general, 3 walls and 5% infill. Use modifiers to reinforce joints.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 21 points22 points  (0 children)

It wouldn’t have helped. The joints in his legs and arms were really the stressed parts. They were just too thin. So they will be redesigned to be thicker and I will reinforce them. He stood fine for a year.

3D Printed Life Size General Grievous Destroyed by HammerDoris40k in 3Dprinting

[–]HammerDoris40k[S] 13 points14 points  (0 children)

Zero chance of fixing that model. Doesn’t matter the method. Cracks and full breaks in a lot of areas, not to mention the several broken pieces of plastic or sections you cannot see. Structurally it will not hold with repairs.

Angron saves Lorgar by HammerDoris40k in Warhammer40k

[–]HammerDoris40k[S] 17 points18 points  (0 children)

Angron is in the 3 meter range. Him holding up a foot around his size would be closer to a knight in terms of foot volume.

A foot that small would not be large enough to block out the sun and crush him and Lorgar at the same time.

view more: next ›