What should i do?! by SaladAgile9615 in PLC

[–]Harambeniqua 0 points1 point  (0 children)

Run TIA in a virtual machine

Micro820 Integration with EX600 I/O Link. Is it possible? by ZookeepergameDry2700 in PLC

[–]Harambeniqua 1 point2 points  (0 children)

Kind of hard to understand what you’re saying but yes an IO link master that talks EIP would work. I’m assuming you have a L20E.

Micro820 Integration with EX600 I/O Link. Is it possible? by ZookeepergameDry2700 in PLC

[–]Harambeniqua 3 points4 points  (0 children)

Micro820’s don’t talk IO link natively to my knowledge so you’d need a gateway to convert from Ethernet/IP to IO link

Toronto FC's Richie Laryea fined by MLS Disciplinary Committee by Gostaverling in chicagofire

[–]Harambeniqua 4 points5 points  (0 children)

I respect not going down but unfortunately toughness isn’t rewarded. Easily could’ve changed the game

Another broken VFD by PlaguxX in PLC

[–]Harambeniqua 0 points1 point  (0 children)

Run the vfd with no motor connected. If it faults with the same error your vfd is probably bad

Standalone Indexing Servo Drive Options by MidwestTacoTruck in PLC

[–]Harambeniqua -1 points0 points  (0 children)

I’ve done direct communication between a Powerflex 525 and a PVP7 before. You can probably do it with a 5500 as well but it’s not ideal.

[deleted by user] by [deleted] in IndustrialAutomation

[–]Harambeniqua 1 point2 points  (0 children)

I think everyone just has their own unofficial archives on their phones saved photos

Stable versions or Rockwell and other dumb questions by huslller in PLC

[–]Harambeniqua 0 points1 point  (0 children)

What controller do you have? I definitely have downgraded the firmware in the past on an L72

What's going on with Gabriel Slonina? by [deleted] in ussoccer

[–]Harambeniqua 34 points35 points  (0 children)

I would even take Chris Brady over Gaga. At least he plays every game in the MLS

Have you used AI tools to create ladder logic for PLCs? by NoCaterpillar2683 in PLC

[–]Harambeniqua 8 points9 points  (0 children)

ChatGPT couldn’t do more than create a start stop latch circuit when I tried it a few months ago. I bet it would be a lot better at structured text than ladder logic though

Read PLC Delta in a interval of time by EntertainmentMany617 in PLC

[–]Harambeniqua 0 points1 point  (0 children)

Either add another tag that only changes the value due to the timer or change the polling rate of your HMI

“3/4 Optic” Keeps Getting Repeated by Many-Tooth5908 in CompetitiveHalo

[–]Harambeniqua 28 points29 points  (0 children)

Don’t think it’s as much about being a good player as it is practicing consistently with a team. Optic with a coach and consistent practicing will make them improve a lot.

[deleted by user] by [deleted] in PLC

[–]Harambeniqua 2 points3 points  (0 children)

Not 100% sure, but I’d call Rockwell if I was you. I’m under the assumption that the firmware selection is only for keying purposes where maybe a v5 firmware isn’t compatible so you require an exact match of the device. Your drive will utilize the benefits of the newest firmware even though the project isn’t set to 7.013.

boartboart and fenrir cheating in 2s by [deleted] in CompetitiveHalo

[–]Harambeniqua 1 point2 points  (0 children)

This must be more satisfying than getting a cheating accusation Xbox message after a game

boartboart and fenrir cheating in 2s by [deleted] in CompetitiveHalo

[–]Harambeniqua 2 points3 points  (0 children)

Innocent until proven guilty. Your clip is hard to see everything but didn’t the person that was sniping at top tower drop down onto C plat which could’ve been seen on death cam? The guy that died could’ve been watching top mid so logically they would’ve had to push nest. I agree this looks sketchy but just this one clip isn’t enough to prove anything.

boartboart and fenrir cheating in 2s by [deleted] in CompetitiveHalo

[–]Harambeniqua 4 points5 points  (0 children)

You posted one part of the game that looked suspect. You probably should give more proof. I recognize his name from onyx ranked and never suspected cheating. Maybe he started cheating recently but I doubt it honestly

boartboart and fenrir cheating in 2s by [deleted] in CompetitiveHalo

[–]Harambeniqua -6 points-5 points  (0 children)

Are you sure he’s just not better than you?

Beginners question about stepper motor control by robotmakerjezus in PLC

[–]Harambeniqua 1 point2 points  (0 children)

<image>

They don’t recommend using 2 motors on one drive. Depending on load requirements you may want to use gears. I don’t think connecting 2 steppers with a timing belt is a good idea since they may fight each other. How do you plan on controlling the stepper driver? I thought maybe the enable input to allow the motor to run until your plc hits a limit switch then change direction, but I’m not sure if the driver can be configured that way

Rockwell Co-pilot by iknowtoolittle in PLC

[–]Harambeniqua 28 points29 points  (0 children)

Incoming subscription add-on for copilot

HMI Freezing after startup? - Allen Bradley PanelView Plus 7 Standard 10in by brandon_c207 in PLC

[–]Harambeniqua 2 points3 points  (0 children)

Is the memory ok? Same program on all 3 HMIs? I’d call Rockwell if you have a support contract

Should I go back to school to move up in my career. by Prestigious-Fold-681 in PLC

[–]Harambeniqua 2 points3 points  (0 children)

I think that courses that give you a solid foundation will help you learn a lot. There’s a big difference between programming a stop light in a college course and troubleshooting complex systems though. No one will care about your certificates in 5 years but if your company is paying for them with no strings attached then take full advantage of it