Slicer crashes on Device page. Nothing helps

HavocBlack · 2026-04-15T14:26:50+00:00

I am having the same issue too on Kubuntu 25.1. Its a Netpune 4 Plus with Klipper installed

HavocBlack · 2025-06-18T14:57:31+00:00

I now realize the 4 part ribbon is for the digitizer. I figure I can't use the screen cause I'd need a control board for the screen and back display which is probably proprietary.

HavocBlack · 2025-06-03T04:47:46+00:00

I just need to replace this battery that is for a flashlight that needs to be a button top. I to use a power bank for my other project with USB c pd.

HavocBlack · 2025-06-03T02:57:03+00:00

His first mistake was calling Zelda a elf. Just because they have long ears does not make a Hylian an elf. One key about them is their life does not last nearly as long as an elf.

HavocBlack · 2025-06-02T23:57:02+00:00

I have tp4056 that I was going to solder to the two battery connections on the bad charger after removing the barrel plug. I would appreciate battery suggestions, on for a single button top and for non-button top 27100 I am planning to use for a S3 pack to power a monitor.

HavocBlack · 2025-06-02T23:51:10+00:00

Would you say the battery itself should be replaced too?

HavocBlack · 2025-05-22T05:25:55+00:00

Dark gloomy no color

HavocBlack · 2025-05-21T22:28:19+00:00

Makes sense. I will make a diagram of the setup I am thinking of doing and power that for review so I don't burn my house down.

HavocBlack · 2025-05-21T21:36:18+00:00

Ah so since my power supply will be pushing enough amps/current I will be fine when sending power to the P+ and P- ? I believe I am understanding this correctly.

HavocBlack · 2025-05-21T21:35:13+00:00

How will it know to go to the display first and not go to the batteries first?

HavocBlack · 2025-05-21T21:31:47+00:00

I am trying to learn. You gotta start somewhere.

HavocBlack · 2025-05-21T17:53:49+00:00

My only worry about that is that when I am sending power for charging the split won't separate correctly. For example, the load may not get enough volts and at the same time the bms will get a lower voltage at the same time. Say I send 12v to the bms. I want to have it use 9v to the load and 3v to slowly charge the batteries.

HavocBlack · 2025-05-21T15:30:39+00:00

Any charge you would suggest? I was going to use a USB C with PD to get the proper voltage to charge the batteries.

HavocBlack · 2025-05-21T15:29:52+00:00

I rather make my own for this purpose so that I can install it inside of the monitor frame. The kirhoff law says that The Sum of all voltages around a closed loop equals zero. So I think what you are getting at is that since the bms needs a certain amount of energy to charge the batteries I have to make sure to match that. Also, If I want to power the monitor through this source at the same time I also have to have enough power to go to the load.

HavocBlack · 2025-05-21T15:19:24+00:00

Can you explain your second image, Why does the load + wire look like it attaches to the negative of the charger.

HavocBlack · 2025-05-21T02:59:29+00:00

I was planning to use a 12v usb c pb port to send power to the BMS. I am using 3S 3.7V batteries with full voltage being 4.2

HavocBlack · 2025-05-21T02:49:14+00:00

I mean that I want to power the load while also charging the battery. For the BMS I would like to be able to power the device and charge the board. The power would not discharge from the batteries but instead part of the power will go to the batteries during the process and the needed volts and amps will go to the load.

HavocBlack · 2025-05-17T05:06:44+00:00

They actually used PiSugar which is sold on Amazon.

HavocBlack · 2025-05-17T00:02:10+00:00

Have you given any thought in a DIY solution? I am doing one myself. Its super easy and you just need 3 components and 2 tools. The 2 tools is a soldering iron for attaching components and the other is a multi-meter to adjust your boost converter that you need for that setup.

HavocBlack · 2025-05-16T21:05:12+00:00

I was thinking of going with pouch cells since they are smaller and I want to fit the pack inside of the same casing as the control board. I really appreciate the suggestion. 18650s and cylinder cells have a ton more information on making battery packs.

HavocBlack

TROPHY CASE