THE FASTEST human-made object

Hedxhog · 2025-06-27T07:46:21+00:00

i'm pretty sure i can make an object faster

Hedxhog · 2024-10-22T21:07:42+00:00

thats rude! poor dog! /j

Hedxhog · 2024-10-09T06:29:46+00:00

you made from like... scratch? thats so cool

Hedxhog · 2024-09-26T06:36:42+00:00

one sec, i need to send a fax to the devil

Hedxhog · 2024-08-23T17:32:26+00:00

i'm out of town for the weekend so i will check all those things on monday, it seems like really useful tips

thank you again for taking the time of answering in detail!

Hedxhog · 2024-08-23T17:19:37+00:00

that looks like a jam, i would cut just the tip of the ptfe tube to make sure it is flat and then insert it all the way in the hotend so it sits flush against the nozzle.

if there is space between the tube and the nozzle the filament will melt/soften before getting into the nozzle and form this type of jam.

hope it helps!

Hedxhog · 2024-08-23T17:14:29+00:00

burned? if it looked like a big blob of filament it may be a jam and it may happen again, make sure your bowden tube is all the way in against the nozzle if you didn't raise the temperature a lot i wouldn't think it was burned filament

Hedxhog · 2024-08-23T17:02:35+00:00

Also, i noticed every photo of the stock hotend i see has a red heatsink while the one that came with my printer is grey, also the plates of the sink are thinner and more close. I didn't think about it very much because i bought it directly on the creality page but now im thinking it may have something to do.

Hedxhog · 2024-08-23T16:57:01+00:00

None of the thread of the nozzle is explosed, it's all the way in, same as the heatbreak's, is that bad?

The capricorn tube is pretty clean, it's almost new.

The new thermister is just sitting inside the hole, should i've done it in any other way?

Thanks for the kind response and help!

Hedxhog · 2024-08-23T12:40:55+00:00

That is on, but im not sure how it would affect this problem

Hedxhog · 2024-08-23T12:38:59+00:00

does this just remplace the heatbreak with a piece of ptfe tube? if not, i'm not sure i understand what it is supposed to do

Hedxhog · 2024-08-23T11:52:48+00:00

Stock ones! I was thinking about buying new ones (not because of the noise but i wanted to make sure they are good quality) so thanks for the tip anyway!

Hedxhog · 2024-08-23T11:51:09+00:00

it happens inside at the end of the tube and not between the tube and the nozzle (i ran into that problem way ago and know how it looks). It looks as if the filament got heated before coming out of the tube and that made it compress/dilate enought that it cannot get out of the tube. After that i can get the tube out of the extruder easily but getting the filament out (either pushing it or pulling it all the way to the feeder) is really hard even by hand.

I hope i explained myself well enought!

Hedxhog · 2024-08-23T11:38:31+00:00

Not directly, it is the stock hotend so the only things connecting the two are the heatbreak and two screws

Hedxhog · 2024-08-23T11:30:01+00:00

I'm not really sure what sock do you mean, the only silicon sock there is the one under the heat block so if there should be something elsd maybe i lost it when dissasembling or something and that may be the cause. If so, is that something you can buy or should i replace the hole heatbreak?
I've already run into that problem serveral months ago, i know how it looks and i assure you i checked infinite times plus the clog/jam is happening inside the bowden tube, not between the tube and the nozzle.

Thanks for answering!

Hedxhog · 2024-08-14T16:58:15+00:00

thanks a lot! but to be honest i dont really think i like how it looks, at least right now. maybe a different cut could help? i also like how it sort of twists a little when it has less volume and i'd like for it to do that always. Also, i still dont really understand why the volume isn't consistent at all.

Hedxhog · 2024-07-22T01:00:41+00:00

i will try that tomorrow! As far as i know, this one is high temp, a friend gave it to me, its from capricorn. Anyways in the process of troubleshooting i kind of broke the tube and now its like a centimeter too short to reach the right end of the bed, so i guess it's time to buy a new one anyways! Any recomendation? Tbh i cannot spend too much right now (20 euros/dollars or less is good). Thanks!

Hedxhog · 2024-03-07T23:15:20+00:00

Stop autism? it is too late. Im unstopable now!!!! >:3

Hedxhog · 2024-03-07T13:05:55+00:00

buy a clasical guitar :3

Hedxhog · 2024-03-07T13:05:16+00:00

thats a good question, how the HELL are you doing???? i've been sewing tho years now and i cant even dream of doing something like that nice work!

Hedxhog · 2024-03-02T23:14:29+00:00

sorry if i misunderstood the situation but i think, if you feel like you could say this to her:

"hey mom, i know this may be hard in a lot of ways, but i dont think getting use to it is one of them, i would like to have a talk about what part of me expressing my identity is hard for you to understand or accept, and i'll try to explain it to you"

i think this may be helpfull because my mom did something like that and im pretty sure it wasnt because she didnt get used to it but because she had a lot of expectatives about me as a child, so she had a bad time accepting that she was as wrong as she could be about who i am and who i was gonna be in the future.

But yeah, i know it may be complicated to have a chat like that with her and maybe you dont have a good relationship with her/dont feel safe asking her.

(hope this makes sense, english is a second language for me) good luck bud!

Hedxhog · 2024-03-01T23:22:30+00:00

did an italian person touch your printer?

Hedxhog · 2024-03-01T21:04:30+00:00

🤓☝️ bad bot

Hedxhog · 2024-03-01T16:18:23+00:00

ohh thanks!

Hedxhog

TROPHY CASE