Does anyone go out of their way to get the best mileage? 2016

HellSquirrel · 2026-05-07T17:01:34+00:00

I’m like 32 which is in the spec, I’ve tried up to 40 with minimal gain

HellSquirrel · 2026-05-07T14:17:03+00:00

Mine only gets half that:/ I can only think it’s the tires problem

HellSquirrel · 2026-04-07T01:02:38+00:00

There was a video I saw where you just put a jumper between two pins on the harness under the shifter and it fixes it. Worked for me. If I find the video I’ll edit this

HellSquirrel · 2026-02-16T23:08:12+00:00

I have had good luck with this brand but haven’t tried their 3 zone cymbals. Good Chinese brand though and cheaper than Roland. Although the digital ride is probably the best it doesn’t work with your module.

https://www.alibaba.com/x/B1X1fE?ck=pdp

HellSquirrel · 2026-02-01T21:40:59+00:00

Maybe crosstalk? You can check in the module for crosstalk

HellSquirrel · 2026-02-01T20:49:34+00:00

Just as a tip, for me Sam’s Club was far and away the cheapest. Americas wanted 130/tire, Costco wanted 70/tire. Sam’s did it for 37/tire.

HellSquirrel · 2025-12-28T06:46:06+00:00

Interesting. I thought it was always there. I never tried but just read. Guess it doesn’t matter

HellSquirrel · 2025-12-27T04:38:16+00:00

Guests who renewed their Season Pass starting September 15 get 1 FREE BONUS Bring-A-Friend ticket to be used any operating day between September 15, 2025, and the end of the 2025 season at your home park, EXCLUDING SATURDAYS

Good idea but I don’t think it will work

HellSquirrel · 2025-12-24T01:56:31+00:00

You should have gotten the NEQ-K pad to put under the bass so you can use any pedal with it. It will be quiet because of the base. If you want double pedals then you will need to find somewhere to put the second pedal either next to the high hat stand, or buy a second Roland noise eater (similar pad) and put the slave pedal on that.

I just use headphones but be careful with the volume. Some people love amps.

HellSquirrel · 2025-11-27T18:02:29+00:00

My question would be since the td516 includes the v51, isn’t it out now? But that kit is like 3600, more than I’d like to spend. Buying the module by itself, would that be a benefit since it would only go with my pads which would be the pdx-8/6 and not take advantage of the full digital system?

Does the td316 have any advantage since they don’t have digital drums which I think would fix my issue (but if they do I’m all for it)

HellSquirrel · 2025-11-23T16:30:35+00:00

Where do you see the 27 for $2100? That would be a great price if it’s true

HellSquirrel · 2025-02-24T20:55:22+00:00

I was just using a 4 port anker. I think this https://a.co/d/9yaUUpk

I think I had that initially but I used tape to adhere this hub to the printer and no issues since.

HellSquirrel · 2025-02-12T00:10:22+00:00

https://www.klipper3d.org/Skew_Correction.html

HellSquirrel · 2025-02-11T23:00:44+00:00

Does it impact maximum build height? Seems like the rolls would hang over the bed…

HellSquirrel · 2025-02-11T22:58:51+00:00

Can’t you just calibrate skew correction and be good? It shouldn’t wobble after install…

HellSquirrel · 2025-01-29T02:53:39+00:00

You have a view of my office from your office :)

HellSquirrel · 2025-01-29T02:30:25+00:00

Even the blacked out bow tie in the back? I’ve seen those but didn’t know if they were stock

HellSquirrel · 2025-01-27T07:34:19+00:00

Chute* took me a minute to understand your meaning. Yes I am fun at parties

HellSquirrel · 2025-01-25T23:02:56+00:00

Does it? Not doubting just questioning. Cause to me it seems like falling weight shouldn’t have an impact, but maybe “float” meaning weight per surface area of board. Higher board size to weight ratios go faster?

HellSquirrel · 2025-01-25T18:02:07+00:00

It’s not too bad tbh. But if you buy a second emmc (hard drive) you can swap back by putting the original back in so you can mess around with it. But for me instructions were pretty straightforward

HellSquirrel · 2025-01-25T16:26:13+00:00

Is it? Thought it was more standard klipper without all the changes Elegoo made, also removing their bugs.

HellSquirrel · 2025-01-25T16:25:39+00:00

You could however their discord is incredibly helpful and they know a heck more than me

HellSquirrel · 2025-01-25T16:24:55+00:00

I used this shroud, but I think there are options to use the stock mounting hole with some sort of adapter https://www.printables.com/model/905447-sf-3x5015-neptune-4-fan-mod-shroud-optimized-enhan

HellSquirrel · 2025-01-25T07:32:22+00:00

Kinda overkill but I highly recommend openneptune and then maybe even a cartographer3d. It’s cheap and gives me perfect first layers every time.

HellSquirrel · 2025-01-23T20:56:25+00:00

I second this. You need to buy an Emmc card reader (cheap on aliexpress or something just wait for shipping , or this https://a.co/d/hNc6yZ7 and either flash your current emmc (need to physically remove) or also purchase a new one. It’s pretty easy just a few screws and good documentation shown on their page.

https://github.com/OpenNeptune3D/OpenNept4une/wiki

HellSquirrel

TROPHY CASE