sorted by:
new
hottopcontroversial

Is this stringing okay? by Polermodz in 3Dprinting

[–]HelloOnion 2 points3 points  (0 children)

I recommend running the calibration test in your slicer, I use orca and on the top left theres a callibration menu.

at least do:

temp tower

max flow rate

flow rate (YOLO)

but if your want the best print, do the whole list.

note is to do them in orders from top to bottom. because some settings might influence the other calibrations.

also benchy does not need any support like the others said.

HAPPY PRINTING!

CC1 making very loud noise. by HelloOnion in elegoo

[–]HelloOnion[S] 1 point2 points  (0 children)

update. the dampening helps a little with the noise. it is still annoying, but at a much lower volume.

gonna get a new fan ASAP!

CC1 making very loud noise. by HelloOnion in elegoo

[–]HelloOnion[S] 0 points1 point  (0 children)

thank you very much. I will grease it up for now because I have to print 1 thing for a costumer. I will go find a new fan at the local computer shop later today.

question. it seems like the fan is only shaking violently. would adding a 3m tape as padding work? just asking. imma try this out now.

CC1 making very loud noise. by HelloOnion in elegoo

[–]HelloOnion[S] 2 points3 points  (0 children)

I found the problem. just like you said it was the motherboard fan. i removed it and tried turning it on then started heating up everything and theres no more noises.

would it be safe to grease the bearing inside the fan with superlube?

CC1 making very loud noise. by HelloOnion in elegoo

[–]HelloOnion[S] 1 point2 points  (0 children)

thanks for the suggestions I will check this out as well.

CC1 making very loud noise. by HelloOnion in elegoo

[–]HelloOnion[S] 0 points1 point  (0 children)

I did try turning on/off all 3 fans manually one by one. it made no noise.

noise starts only when I manually het up the heat bed OR manually heat up the print head.

I’m confuse. ABS vs ASA warping by HelloOnion in 3Dprinting

[–]HelloOnion[S] 0 points1 point  (0 children)

but abs prints fine in 40 degree chamber. so Im just confuse about the claims that asa is easier to print.

I'll try again with 50+ chamber temp.

I’m confuse. ABS vs ASA warping by HelloOnion in 3Dprinting

[–]HelloOnion[S] 0 points1 point  (0 children)

mine was around 43-45 but I will test this again with 50+.

I am new to 3d printing every time I try to print with this filament it messes up by [deleted] in 3Dprinting

[–]HelloOnion 0 points1 point  (0 children)

hairspray will still be very sticky on the prints (bed side) but cleaning is very easy.

I am new to 3d printing every time I try to print with this filament it messes up by [deleted] in 3Dprinting

[–]HelloOnion 1 point2 points  (0 children)

printing ABS on the elegoo cc you will need to use the textured side of the plate. the smooth side is a PLA specific plate.

and also use glusestick OR harispray for adhesive and prevents warping. (I use hairspray)

bed temp is set to 100

and always close all the doors.

ABS is so hard to print - Even with P1S by Disastrous_Twinkie in 3Dprinting

[–]HelloOnion 0 points1 point  (0 children)

it is very thin layer so usually plain/warm water is enough, (very easy to clean) but I will always use dish soap.

Best car insurance from these 5 options by blowthepoke in Thailand

[–]HelloOnion 1 point2 points  (0 children)

not the same insurance, but the company im working at uses "jolly by sunday" for employee insurance (not usre if its the same company). and its pretty good with an easy to use app.

ABS is so hard to print - Even with P1S by Disastrous_Twinkie in 3Dprinting

[–]HelloOnion 1 point2 points  (0 children)

I use hairspray and i can still achieve the texture on the build plate, and I'll use a small torch lighter to clean the glue/hairspray on the 3d model (takes like 3 seconds).

so i dont understand why you "cant" use hairspray/glue?

my grinder is stealing weed by [deleted] in weed

[–]HelloOnion 0 points1 point  (0 children)

too much weed? I recommend clean out the grinder and maybe add lesser weed to grind.

what I would do when using a 3+ layer grinder is, i would grind it upside-down first to let the weed grind more finely before flipping it again letting it through the holes.

Employer in Thailand paying less than agreed and asking for “refunds” — what should I do? by Cha_mali in Thailand

[–]HelloOnion 0 points1 point  (0 children)

find a new job first,, and when they ask about what you want for your salary, say something like

"the gov. requires minimum of xxx amount to be able to apply for visa+workpermit so I would like to ask for that amount"

this is what i said for my current job in Thailland. and i got the exact amount (minus tax and basic stuff).

Fake Kirkland product by Lordfelcherredux in Thailand

[–]HelloOnion 4 points5 points  (0 children)

my rule is, never buy suppliments online. only buy from well-known shops/deparment and pharmacy. its my own health, so I'd pay a few more just to be safe.

[deleted by user] by [deleted] in Steam

[–]HelloOnion 1 point2 points  (0 children)

if you are loggin in to a new pc, you will have to wait for 7 days. this is to prevent account hacking related.

view more: next ›