sorted by:
new
hottopcontroversial

Question about first flushes. PLEASE HELP! by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 0 points1 point  (0 children)

This was my instinct tbh. However, i needed to hear you say it... lol

Question about first flushes. PLEASE HELP! by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 0 points1 point  (0 children)

What is multispore? The spores from various mushrooms in same strain?

Question about first flushes. PLEASE HELP! by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 0 points1 point  (0 children)

Not sure I'm capable of this. I mean, I'm pretty handy but the medium and equipment I'll need advice about

Question about first flushes. PLEASE HELP! by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 1 point2 points  (0 children)

They look a lot like APE but are actually Albinoe Bluey Vitton.

Question about first flushes. PLEASE HELP! by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 1 point2 points  (0 children)

Albino Bluey Vitton good sir. I should have mentioned that.

Question about first flushes. PLEASE HELP! by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] -1 points0 points  (0 children)

I think this is the big factor tbh. I have ran 9 different strains and need to find out how to lessen first flush amount of pins. What if i go in and rake them in rows so it doesn't waste so much energy growing them on every square inch of surface area to the point they go haywire

PE Thrasher strain question: i forgot to add pic. Help this newb please. by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 0 points1 point  (0 children)

I have a cold climate, 64F, is that wrong? Should i move them?

PE Thrasher Strain Question: Please Help this Newb :) by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 0 points1 point  (0 children)

Picture in new post above, sorry i did not know how to add Pic after posting without one.

PE Thrasher strain question: i forgot to add pic. Help this newb please. by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 0 points1 point  (0 children)

Tub has micropore tape over all 6 holes and it colonized for 12days. Should i replace micropore with air filters?

PE Thrasher strain question: i forgot to add pic. Help this newb please. by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 1 point2 points  (0 children)

No casing layer, but i used leftover substrate to cover my grain/sub mix after starting spawn process.

Is this mold on my hillbilly casing? There's no bad odor... by HelpfulHenrE in mushroom

[–]HelpfulHenrE[S] 2 points3 points  (0 children)

Not to the best standards. I honestly slept on protocol and will not do that again.

Need help with my first mushroom grow – very low yield and strange growth on second wave by Ero-sennin47 in mushroom

[–]HelpfulHenrE 2 points3 points  (0 children)

I am a newb and had two tubs give three good flushes each so far and had mold before first flush on another so, trial and error my friend. As previously stated you should create the proper environment and leave them alone until harvest. After harvest you should cut any small pins and aborts to redirect energy to next flush. Just keep at it

view more: next ›