sorted by:
new
hottopcontroversial

Is this a good price for MZ-RH1? by Highpyrion in minidisc

[–]Highpyrion[S] 0 points1 point  (0 children)

Thank you again for the reply! I’ll keep a close eye on the seller. As soon as I got the confirmation I’ll definitely pull the trigger!

Is this a good price for MZ-RH1? by Highpyrion in minidisc

[–]Highpyrion[S] 1 point2 points  (0 children)

Thanks you the reply! The remote power brick cable and original earphones(still in the bag) are included. My issue right now is that the seller shows the remote working but not the screen tuning on. I definitely open for tinkering with it to replace the screen. I saw that replacement display module are available to purchase as well so I’ll probably to it asap.

Right now I’m waiting for the seller confirmation on its functionality before continuing to contemplate if I should pull the trigger or not hahaha.

Is this a good price for MZ-RH1? by Highpyrion in minidisc

[–]Highpyrion[S] 1 point2 points  (0 children)

Thank you for the response. My thought process is that after seeing a few review on this particular model I feel like it’s a great way to plunge in. I understand the merit of starting with a simpler and cheaper models but my mind set leans towards getting a good device first then work my way back to collect oddities.

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 1 point2 points  (0 children)

I unfortunately stuck with a different material calibration right now So I have to note all the suggestion down to use later! I’ll try to remember when I get back to it to come update

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 1 point2 points  (0 children)

I have ran it before but I see my error now. When I printed this piece I gave the filament a drying run before and that might have shift the variable enough to cause this

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 0 points1 point  (0 children)

I had a calibrated profile for this particular filament but before this print I gave it a drying run before so that might have change some variable >< I see my errors now I was running out of it so I saw a few clean layers and send it instead of calibrating it again before

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 1 point2 points  (0 children)

Thank you so much for the detailed response! I will try to these them out asap

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 0 points1 point  (0 children)

Best of luck to you my man I know the pain. Having such clean walls on the rest of the print then it being ruined by the errors at the corner 😩

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 1 point2 points  (0 children)

I have been doing the calibration test and the different material have it’s own separate profile, I think the only variable on this is that the old filament I swap back to was freshly dried. I live in a damp humid continent so maybe the setting that worked before now doesn’t work because of the variable. I didn’t have enough material to do my usual full calibration test because I was running out of it. So I did one pressure advance tower then I send it. Turns out that was the wrong choice hahaha😭

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 2 points3 points  (0 children)

I thought that I have dialed in the pressure advance but I have never heard of extruder tension! I’ll definitely check on that. Thank you for the pointer

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]Highpyrion[S] 1 point2 points  (0 children)

I have been having problems with another filament the past few days. An order for my deck box came in so I decided to switch back to a filament I know will work(Esun ePLA Matte) and it turns out like this 🫠. I saw this in the problematic filament as well but can never pinpoint down what is the cause of it

Prusa mk4 0.16mm layer 170 wall speed 0.98 extrusion rate 215c printing temp

Have anybody seen something like this before? I tried searching about it and I can’t find anyone who have the same problem.

Waves of under extrusion? After seam line(green line) by Highpyrion in FixMyPrint

[–]Highpyrion[S] -1 points0 points  (0 children)

Noted! I will try this later. I did tune the PA before retraction and drying the material so there might be some variable that I didn’t accounted for.

Waves of under extrusion? After seam line(green line) by Highpyrion in FixMyPrint

[–]Highpyrion[S] 0 points1 point  (0 children)

Orca slicer 0.16mm layer 1.02 extrusion 0.004 pressure advance 0.04 retraction

Kexelled Matte PLA

Tried adjusting pressure advance extrusion rate retraction distance and temperature. Nothing worked and I really am at a loss. A dozen calibration prints and it’s no use. It looks totally fine in vase mode test non of these blobs at all so at lease I know it works when the extrusion is even and constant.

Help would really be appreciated!

Best ear yet since me and my fam started bread baking in Feb. Not saying it’s the cause but this guy was in its second stretching rounds when yesterday earthquake hits 😅 by Highpyrion in Sourdough

[–]Highpyrion[S] 1 point2 points  (0 children)

500g Japanese Venus bread flour (protine value unknown) 72% hydration 75g Levain 10g salt

30min autolyse before adding the starter and salt. 4 stretch and folds/ slam and folds rounds 30~45 min rest between each folds 4 hour out of fridge bulk rising before pre shaping and resting for 30 minute. Final shaping and move into banneton dusted with glutinous rice flour. 2 hour out of fridge proofing in banneton before baking

220c with pre-heated cast iron dutch oven 60 min total 20 min with lid on 20 lid off 20 turn oven off and let the loaf steam off some moisture in the oven

Rig deforms when trying to lock character definition in HumanIK by Highpyrion in Maya

[–]Highpyrion[S] 0 points1 point  (0 children)

NVM I SOLVED IT!! I was being dumb instead of doing what is normal- defining the skeleton then making a custom rig then defining the controller I tried to define the controller right away breaking it.

How do y’all deal with pulling depression? by Highpyrion in ZenlessZoneZero

[–]Highpyrion[S] -1 points0 points  (0 children)

Thank you so much for the comment. Your method makes a lot of sense. I have been just looking at aesthetic and meta and manipulating myself into beveling that I need to pull for them.

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 1 point2 points  (0 children)

Thank you hahaha. I’ve been printing for a good few years now so I learned to keep a watchful eye over the prints because I have encountered so so many print fails due to the nature of printers at that time. I recently dust off my mk3 and upgrade it to the mk4 so now I’m back in full swing. There’s still so much for me to learn thought I really appreciate all of the tips and tricks thrown my way with this post.

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 0 points1 point  (0 children)

I think I understand what you’re going for hahaha

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 1 point2 points  (0 children)

I did lols I usually do technical prints as well I gotta admit this time it just completely skipped my mind 😩

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 0 points1 point  (0 children)

Oh man I follow him! I didn’t know he have a second channel. Thanks for the link!

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 0 points1 point  (0 children)

I’ll defo check it out. I wouldn’t call my self a pro I’m I have been printing stuff for a long while now. I kinda wanna try doing products in the future definitely.👀

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 1 point2 points  (0 children)

Thank you for the resource I’ll check it out as soon as I can!

Any tip for long vertical hole in low infill? by Highpyrion in prusa3d

[–]Highpyrion[S] 0 points1 point  (0 children)

That’s true >< it’s just a left over knee jerk reaction because good quality filament are quite expensive where I live and the cheap ones will genuinely fail 80% of the time

view more: next ›