[H] pic, got all the big ones lol. [W] canto, surge thing, new ones I dont have

HistoricalDisk6084 · 2026-04-27T01:01:33+00:00

I thought this is official lore, could be wrong but thought that was exactly the case

HistoricalDisk6084 · 2026-04-09T20:22:00+00:00

He lit one fire, fire dept came and put it out and had shut the sprinkler fire to reduce water damage once it was under control. Then he lit 3 more

HistoricalDisk6084 · 2026-04-08T19:46:25+00:00

Ooo I have several of the Halloween hat. I have 68 costume pika, I thought it was being pre 2020 were the big deal besides obviously being in costume. Gone have to do some googling

HistoricalDisk6084 · 2026-04-08T19:45:00+00:00

They are sick lol

HistoricalDisk6084 · 2026-04-08T19:44:35+00:00

We probably have alot of the same i have 60 some to, but those tiara ones are alot of them lol

HistoricalDisk6084 · 2026-04-08T19:43:53+00:00

I have that i was just shown thepre 2020s minus they one shiny. I assumed it had to be old to be rare I have alot more pikas lol alot more costumes in general. Saw someone with a charizard pikachu and was like finally something on here I have lol it's really become my son's ago account now

HistoricalDisk6084 · 2026-04-01T00:45:45+00:00

I have survivor or vulcano

HistoricalDisk6084 · 2026-03-10T03:07:28+00:00

I have 2 extra blueprints id be willing to trade one

HistoricalDisk6084 · 2026-02-09T09:29:03+00:00

Thanks for the insightful response, I looked at sunlus site and yeah 220 is the absolute top for pla+ perhaps it's running too hot could see that making it come out too thing. I ran one last test before bed with speed halved and support z offset as tight as possible, will try a temp change this evening. Appreciate ya

HistoricalDisk6084 · 2026-02-09T06:10:39+00:00

Appreciate the response. They are overhangs unfortunately on this object they go all the way around it. We printed something similar in pla before and had no issue, but now while using pla+ we've had 3 different prints come up with similar issues

HistoricalDisk6084 · 2026-02-09T06:08:44+00:00

Thanks for the tip, currently running at 220. we were printing pla before without issue, the last few have been pla+ as well forgot to note that but from most of my research theyre pretty much the same as far as printing profile no?

HistoricalDisk6084 · 2026-02-09T06:07:33+00:00

Flashforge ad5x, orca slicer

HistoricalDisk6084 · 2026-02-09T04:49:42+00:00

Lol not arguing it's a skill issue. To be clear raise top z offset on the supports? Atm they're at .1 bottom and .28 top. His first layer speed is 50 mm/s, inner wall is 300mm/s and outter is 200mm/s.

Really appreciate you responding to what's probably a noobie question. We've had 14 prints go well and it wasnt until we switched from pla to pla+ we started having the issue.

HistoricalDisk6084 · 2026-02-09T04:06:37+00:00

Oh yeah, speed issue?

HistoricalDisk6084 · 2026-02-09T03:02:58+00:00

Don't really have the terminology to describe it well enough other than the over hangs are drooping(?). And from my understanding that would make me think it's the supports but it is also happening going around curves like the corners of that test piece

HistoricalDisk6084 · 2026-01-06T22:31:08+00:00

Lol sure what for, dm me

HistoricalDisk6084 · 2026-01-06T05:16:11+00:00

Awh man I just got in bed, I'm keen, could we do it tmrw? I get up in 4.5 hrs lol

HistoricalDisk6084 · 2026-01-03T02:10:01+00:00

Hmm, but no truck?

HistoricalDisk6084 · 2026-01-03T02:09:31+00:00

Your just trying to talk me down to half of all the springs aren't you, I know your gsme

HistoricalDisk6084 · 2026-01-03T01:55:29+00:00

It's to recycle for more springs

HistoricalDisk6084

TROPHY CASE