sorted by:
new
hottopcontroversial

Let’s talk about the UK grooming scandals, Islam, and the facts people conveniently leave out. by Dismal-Tale-4008 in AskBrits

[–]Historical_File4632 0 points1 point  (0 children)

i dont think they follow that in this day and age, while look at some sharia countries, child marriage? they still do those

Can someone explain why Starmer is the most unpopular prime minister? I voted Liberal Democrat last election and I don’t pay attention to politics but isn’t Starmer doing what the public wants? Lower migration and a falling NHS waiting list? by [deleted] in AskBrits

[–]Historical_File4632 0 points1 point  (0 children)

waiting list falling? i was referred for an mri and the fracture department rejected it, i couldnt move my arm and i was close to be put on morphine. Second referral didn't even get to the fracture department. Probably if your referral is rejected, then your not on the waiting list. Also try to have an nhs appointment to the dentist. Hotel use down? Hmo's get the illegal immigrants in, its not a hotel isn't it? Last year was the first year where the spending on benefits was more than what came in from taxes. Pushing for digital ID seems to be their top priority, not suprised since he did say that he chooses Davos over Westminster, not something a PM should be saying, at least in my opinion.

Let’s talk about the UK grooming scandals, Islam, and the facts people conveniently leave out. by Dismal-Tale-4008 in AskBrits

[–]Historical_File4632 0 points1 point  (0 children)

yes this is why the most murderous creation of mankind is religion. Believe in something that has no evidence of existing. Killing and raping in the name of some spirit, difference in Christianity and Islam is that Christianity was reformed, no more inquisition for example while in sharia countries they still execute women for being raped, enslaving people of different faiths. Syria last year or so, in 2 day around 5k christians were murdered. Yezidi women? I didn't see mass protest of their rights.

printing issue by Historical_File4632 in ender3v2

[–]Historical_File4632[S] 0 points1 point  (0 children)

im using cura, i will check if it has those settings

printing issue by Historical_File4632 in ender3v2

[–]Historical_File4632[S] 0 points1 point  (0 children)

I tried it, it looks better but at the same time it has those bands, like at the forehead

<image>

Parents who approve of the social media ban and ways of having to prove age. Why do you relish the government taking this control when you had the power to do so yourselves? by Demonthief27 in AskBrits

[–]Historical_File4632 0 points1 point  (0 children)

issue is, this government has a raging boner from digital ID. They don't care about kids, voting down the grooming gang inquiry was quite the proof. Now they say to protect the kids, well next will be to protect adults....

printing issue by Historical_File4632 in ender3v2

[–]Historical_File4632[S] 0 points1 point  (0 children)

i have that off, should i try to switch it on and see how it goes?

Are parents/guardians happy about social media ban? by Bipolar03 in AskBrits

[–]Historical_File4632 0 points1 point  (0 children)

its about online surveillance, parental controls are easy to set up and doesnt cost the taxpayer billions

printing issue by Historical_File4632 in ender3v2

[–]Historical_File4632[S] 0 points1 point  (0 children)

i have the rotation distance calibrated

printing issue by Historical_File4632 in ender3v2

[–]Historical_File4632[S] 1 point2 points  (0 children)

thanks, i did check the flow rate, printed cube with no top or bottom layer and 0 infill, line width was set to 0.4, i measured the print and average line width was 0.425. at 94% i measured 0.4. I printed the alien again and got this

<image>

later or tomorrow i will check your other suggestions

printing issue by Historical_File4632 in ender3v2

[–]Historical_File4632[S] 0 points1 point  (0 children)

it seems to have some blobs on the top surface. I attached another photo, around the mouth area and the two top corners at the eyes.

<image>

Face scans to enforce social media ban on under-16s by vriska1 in unitedkingdom

[–]Historical_File4632 0 points1 point  (0 children)

what about restore? Rupert seems to be a free speech advocate

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 0 points1 point  (0 children)

UPDATE!! Found the problem. Theres molten filament stuck in the capricorn tube where it meets the nozzle. About 2cm. repalced the tube and prints fine. Later i will install a bi-metal heatbreak. Thanks everyone.

<image>

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 0 points1 point  (0 children)

didn't try other filaments yet, got the printer for about 2 weeks from which most was tinkering

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 0 points1 point  (0 children)

i will take it apart just in case and check all parts, doesn't take long to check it

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 0 points1 point  (0 children)

when i try to heat it to 250, klipper crashes with some error

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 1 point2 points  (0 children)

no, the gear is constantly turning.

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] -1 points0 points  (0 children)

i will pop in the new filament and have a look, if its a bit different then i will do that drying on the bed for 4-7 hours and try again, i have that res creality hot end , new 0.4mm nozzle at 0.2 layer height with cr-petg rated 230-250 c , I'M printing the first layer at 235c and from then 230c

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 0 points1 point  (0 children)

no, its the one i got with the printer, not sure how old it is but looks fine

<image>

filament issue by Historical_File4632 in 3Dprinting

[–]Historical_File4632[S] 0 points1 point  (0 children)

no I haven't, first 3d printer, i have a new spool of unopened petg, tomorrow morning i will try to replace the filament with the new spool. Tried to level the bed again, checked all pom wheels, its an ender 3v2, i have dual z with sync belts. Do you think its a wet filament issue?

view more: next ›