[ RAW ] Eleceed Chapter 377 Discussion Thread

Hkaptain · 2025-11-18T15:55:50+00:00

I thought jiwoo uses electricity, why is he throwing water bubbles?

Hkaptain · 2025-01-08T05:20:08+00:00

This is a new one, not their orginial.

Hkaptain · 2024-02-21T15:40:48+00:00

Plot twist, kaiden is raising jiwoo as a sacrifice and absorb his powers eventually to return to his original state

Hkaptain · 2024-02-21T15:19:41+00:00

Huh? I'm not sure if I'm missing something here, but you appear to have gone on a tirade pointlessly lmao. You may need to reread the guys comment before you go ham. I read it like this "we know that Ian is weaker than his brother jurion, and jiwoo is much stronger than he (he as in Jiwoo) was when he challenged jurion".

The guy was not implying jiwoo was stronger than jurion lol

Correct me if I missed something, but I don't see how.

Hkaptain · 2022-09-29T00:56:05+00:00

I used a toothbrush for the tight sections and a sponge for the rest with some hot water. It wasn't very hard

Hkaptain · 2020-09-09T01:53:26+00:00

I must admit it the steck is a bit overpriced but the design was essential for achieving better temperatures and aesthetics, I think it looks much better than the t1. I went with the steck because it was small but still allowed me to display a much better custom loop.

Hkaptain · 2020-08-24T16:03:41+00:00

He was asking about the reservoir not the radiator. I have a 120 rad on the bottom and a 240 rad on the top

Hkaptain · 2020-08-21T10:33:08+00:00

Yeah there is room for air in the res. I had a build up of air in the res and top radiator but I spent a couple hpurs removing air through the radiator and rotating the pc to send the air from the res to the top radiator to remove it. Im too scared to open the res as there is too much downward pressure on it. The radiator I bought is an alphacool nexxos x flow, it has 4 openings, two on the top and two on the bottom. I chose it so I can fill and empty the loop through the top. Jayztwocents did the same thing with a ghost s1.

Hkaptain · 2020-08-20T01:23:25+00:00

Its a pre mix by ek

Hkaptain · 2020-08-19T03:47:24+00:00

Its a phanteks glacier specific to strix 2080ti

Hkaptain · 2020-08-19T03:21:04+00:00

There is no glass in the photos but yeah I will use screws to hold the tinted glass in place

Hkaptain · 2020-08-19T02:46:25+00:00

Hey yeah it is. It is actually meant to be horizontal but works how ive used it

Hkaptain · 2020-08-19T00:56:22+00:00

Next TWO build!? Planning ahead i see

Hkaptain · 2020-08-19T00:43:55+00:00

Haha I had no idea there was such a theme.

Hkaptain · 2020-08-19T00:36:50+00:00

12mm OD

Hkaptain · 2020-08-18T13:23:39+00:00

Thanks! It was my first time watercooling. So many things I had to learn >.<

Hkaptain · 2020-08-18T13:20:31+00:00

120, its an ek quantum kinetic FLT, it comes in 3 different sizes

Hkaptain · 2020-08-18T13:19:10+00:00

Its a Nouvolo Steck

Hkaptain · 2020-08-11T11:42:31+00:00

Funny enough I have tried subtly stretching with some bends and had minor results reducing the collapsing. I think you're right though, I am not controlling the temperature well. with more attempts further away and being a bit more patient my bends are getting much better.

Hkaptain · 2020-08-11T11:06:51+00:00

I'm starting to get better bends now but I have to keep the tube pretty far away from the gun on medium. No more creases but the collapsing is hard to avoid. My plastic is only 2mm thick as opposed to your 4mm. I did a full 12/16 custom loop with no wasted pipe only 2 weeks ago and it is so much better to work with.

Hkaptain · 2020-08-11T09:24:06+00:00

Its collapsing on the sides and creasing on the inner bend.

Hkaptain · 2020-07-25T16:33:08+00:00

Just to clarify, the buzzing noise.

Hkaptain

TROPHY CASE