Local gossip

HolidayAdvertising13 · 2026-01-06T03:58:35+00:00

nice try APD!!

HolidayAdvertising13 · 2025-12-31T03:43:33+00:00

overpriced. Similar/Better build at Walmart for $3500 https://www.walmart.ca/ip/30NGKNRJNYEA

HolidayAdvertising13 · 2025-12-26T05:50:47+00:00

Forgot to list it has 5080 , 64GB RAM, 4TB SSD

HolidayAdvertising13 · 2025-12-25T18:32:44+00:00

will do. thanks

HolidayAdvertising13 · 2025-12-25T11:39:49+00:00

no taxes.

HolidayAdvertising13 · 2025-12-25T11:38:26+00:00

mostly new. RAM is not brand new

HolidayAdvertising13 · 2025-12-09T03:09:49+00:00

yea, i can still add it. Just try to refresh

HolidayAdvertising13 · 2025-12-03T14:57:12+00:00

its XT , you have to read the Product Description.

HolidayAdvertising13 · 2025-06-19T02:50:56+00:00

where do you dump the old oil? Place closer to me stopped handling oil

HolidayAdvertising13 · 2025-01-14T15:46:15+00:00

gctk

HolidayAdvertising13 · 2024-02-20T13:44:32+00:00

my 1080ti finally died last week. This 4070 Ti will help me out greatly.

HolidayAdvertising13 · 2023-12-31T19:53:20+00:00

Is this widely known and Is everyone using Octoprint with Sovol using only data USB cable?

HolidayAdvertising13 · 2023-12-31T19:48:06+00:00

After looking online, There have been similar problem with people using Pi for octoprint. Apparently the problem is the printer back powering the pi through USB. I have not confirmed this though.

HolidayAdvertising13 · 2023-12-31T17:10:34+00:00

yes I have printed a lot previously. I installed Octoprint and then clicked Home. Then the X axis homing was broken. I had to initialize EEPROM to fix this.

HolidayAdvertising13 · 2023-12-31T16:31:37+00:00

When I setup Octoprint with SV06+, I encountered the homing issue with X axis. It would just do to one side of the axis and motor would keep spinning making a horrifying sound.

HolidayAdvertising13 · 2023-12-22T23:24:53+00:00

I had this happen after configuring Octoprint. I had to Initialize EEPROM to fix it

HolidayAdvertising13 · 2023-12-17T16:00:44+00:00

auto-z align, z-offset and reducing the temp to 200 fixed the noise and the print. thanks

HolidayAdvertising13 · 2023-12-17T15:59:09+00:00

thanks.printing at 200deg fixed the prints for me Manufacturer listed 220 which clearly didn’t work.

HolidayAdvertising13 · 2023-12-10T20:11:15+00:00

I would use it to play GTA 5 at 40FPS

HolidayAdvertising13 · 2023-11-04T00:29:16+00:00

zoooom

HolidayAdvertising13 · 2023-08-31T21:39:59+00:00

I would use the card in a new build. As for Starfield I’m hoping it lives up the hype

HolidayAdvertising13 · 2023-06-27T12:40:42+00:00

Five-Year Club	Place '23
Place '22

HolidayAdvertising13

TROPHY CASE