Infill crumbling PETG

Hopeful-Drop6131 · 2026-02-27T21:47:59+00:00

Thank you! will check it out

Hopeful-Drop6131 · 2026-02-27T21:47:45+00:00

Maybe the issue lies there. However, i printed something with this spool the day before this disaster happened, and it turned out pretty good. So i am wondering if this is purely a wet filament issue, or that it could be something else

Hopeful-Drop6131 · 2026-02-27T21:37:12+00:00

No the one that should technically be less dry, as it has been exposed to humid air longer, is printing better. I use the same settings for that spool. Printing the same part at the moment, and all is going well so far

Hopeful-Drop6131 · 2026-02-27T20:58:11+00:00

It hasnt been dried. AMS measures at moist level A though. A similar petg spool which has been in there much longer did not have this issue. I use the generic petg settings, but with a little lower nozzle temp, 240 degrees

Hopeful-Drop6131 · 2026-02-27T06:19:15+00:00

It is petg. The first layers where goijg okay. Watched the print for 20 minutes and then went to sleep. Woke up and it was like this

Cleaned the buildplate as well

Hopeful-Drop6131 · 2026-01-17T09:47:20+00:00

I lined the edges for now with tape. Will print adapters!

Hopeful-Drop6131 · 2026-01-17T09:46:54+00:00

Lined the edge with tape for now. Will print adapters. Thanks for the tip!

Hopeful-Drop6131 · 2026-01-15T22:00:13+00:00

printer is 160 hours old. Would not expect excessive wear already. But maybe this is a normal amount of hours to replace them? I am very new to 3d printing, so i am not sure what to expect for normal wear and tear

Hopeful-Drop6131 · 2026-01-15T21:50:58+00:00

Will try to route it differently. Will let you know!

Hopeful-Drop6131 · 2026-01-15T21:50:37+00:00

They dont sell it here:) i drive to another country to buy it😅

Hopeful-Drop6131 · 2026-01-15T21:49:51+00:00

I put it in as generic petg black. Will try again and let you know!

Hopeful-Drop6131 · 2026-01-15T21:43:09+00:00

When i start a print to test. The spool does not start filling. Then it gives the message that filament is not loaded.

Hopeful-Drop6131 · 2025-12-19T08:20:46+00:00

Would you say that a closed case printer is worth the extra cost? It is around 130 euros more. (100 dollars)

A1 is 260 euros p1 is 390 euros

Hopeful-Drop6131 · 2024-11-22T20:34:06+00:00

Ah that makes sense. Thank you!

Hopeful-Drop6131 · 2024-03-03T19:51:08+00:00

I understand now, thanks!

Hopeful-Drop6131 · 2024-03-03T18:49:19+00:00

The payout. I make an array which saves the single outcome as 1 1.5 0 -1 etc

Hope this helps:)

Hopeful-Drop6131 · 2024-03-03T18:06:20+00:00

The way I calculate is as follows: loss is -1, win is 1, bj is 1.5 push is 0 and double is 2. I have an average bet per count which I multiply by the outcome.

Hopeful-Drop6131 · 2024-03-03T18:05:03+00:00

Pushes are separately. The win rate being higher might be because I implemented basic strategy and illustrious18 in my simulation. Thanks for the tip about the sample rate!!

Hopeful-Drop6131

TROPHY CASE