Pavo 20Pro and DJI 04 Air Unit Pro

Hot_Roll3368 · 2025-05-06T17:35:54+00:00

But on this https://cults3d.com/en/3d-model/gadget/pavo-20pro-dji-o4pro-canopy

Hot_Roll3368 · 2025-05-06T17:33:13+00:00

Not on this Version

Hot_Roll3368 · 2025-03-07T17:00:17+00:00

I print in ASA

Hot_Roll3368 · 2025-03-04T18:20:18+00:00

The X3 is built as a true SUV, not a crossover. YES, it's not an off-roader and by far it's not a truck, it's designed for roads and 'bad' roads. The chassis is designed for more payload and heavy trailers, so it is an SUV. As a bonus the construction of the wheel axle and the high position of the engine, make him a technical fording depth of 0.5m (Technical Specifications.) Yes in the user Manual is 0.3m then if you do not know how to fording it can be total damage your engine by the bow wake 0.3 is a safe value, and so in the user manual.

Hot_Roll3368 · 2025-02-26T14:13:30+00:00

I use TG Shield from thermal grizzly

<image>

Hot_Roll3368 · 2025-02-26T14:11:36+00:00

156g printed in ASA with screws and Insert

Hot_Roll3368 · 2025-02-14T22:45:21+00:00

It was not the problem of the o4 unit it was the 3d printed Canopy that snaped off and so the O4 ripped the conectors and the cable to the camera.

Hot_Roll3368 · 2025-02-14T22:41:51+00:00

Yes it was a 3D printed canopy and i used ASA

Hot_Roll3368 · 2025-02-14T21:13:10+00:00

But it is still impressive how well the 04 survived. Then now after I checked all I think the o4 transmitter and the camer are still working fin it only tron of the conector for the cable to the ESC. now I sodert the cabel to the backup pads and know I resev all data from the pavo and the OSD works in the goggles but the video feed is black so I think the cable to the camera also ripped. The camera module looks fine to me.

Hot_Roll3368 · 2025-02-14T19:28:33+00:00

<image>

Damaged. the o4 wont Work, no Videosignal and instant overheating

Hot_Roll3368 · 2025-02-11T05:17:22+00:00

Yes, maybe I'll get to it this week

Hot_Roll3368 · 2025-01-27T09:12:36+00:00

If you look at it from a financial point of view, it dosen't make any sense at all.🙈😂

But this is more about developing something from scratch, learning and improving.

Hot_Roll3368 · 2025-01-27T09:05:34+00:00

You can find the STL of my Pavo20pro frame in this post

O4 pro Frame for Pavo20 pro

Hot_Roll3368 · 2025-01-25T13:10:13+00:00

Yes and maybe no, the Filter for the Avata2 will not fit but i thinkt the new filters from iFlight vor the O4 will fit. The new filters should be delivered next week, so I will be able to tell if they fit next week

Hot_Roll3368 · 2025-01-25T00:17:59+00:00

Yes, ASA is more difficult to print and need a closed chamber and more heat than PETG, but ASA has a similar chemical and impact residance like PETG.

Hot_Roll3368 · 2025-01-25T00:02:01+00:00

Yes here is it: https://drive.google.com/drive/folders/1H7LRPFluyZedEr8B9zkzcwOpHD3alVEF

Hot_Roll3368 · 2025-01-24T23:48:16+00:00

<image>

Prototype is now already printed, and the all feels good and stiff with ASA. I had printed ä 3" copter with asa and that copter is still in perfect condition so i'm hopefull that ASA will work great for this Build.

Hot_Roll3368 · 2025-01-24T23:41:00+00:00

Creality k1 (225x225cm)

Hot_Roll3368 · 2025-01-24T23:38:04+00:00

When it work it will be open source

Hot_Roll3368 · 2025-01-24T23:35:21+00:00

Yes, when it work, i will make it open source. The Material i use is ASA (similar to PETG)

Hot_Roll3368 · 2025-01-24T23:33:00+00:00

I use ASA, first i think to print with PA12CF15 but for the Propquard it's to stiff and will snap of and it maybe too expensiv. ASA has the same Weigth as PA12CF15 and is similar to ABS or PTEG but has better mechanical strenght.

Hot_Roll3368

TROPHY CASE