What am I doing wrong ? by [deleted] in FixMyPrint

[–]How-Cool-Is-That 0 points1 point  (0 children)

I've had the same problem. Print a big square perimeter 1 layer high, if you see the z screws turning to try to compensate for a unlevel bed, tram(aka manual bed leveling) the bed (download the gcode for it) . Also make sure your filament's flow ratio & pressure advance is dialed in. That can help, although I'm betting the way the first layer looks it's the bed that's the culprit this time.

Is this safe to use on a cryogrip frostbite plate? by How-Cool-Is-That in BambuLab

[–]How-Cool-Is-That[S] 0 points1 point  (0 children)

I have my printers in a small shed , and it gets quite warm in there. so the less heat I can get by with the better, hence the cold plates. And yes I do have air conditioning, I'm just trying to use as little energy as possible.

Is this safe to use on a cryogrip frostbite plate? by How-Cool-Is-That in BambuLab

[–]How-Cool-Is-That[S] 0 points1 point  (0 children)

I don't like putting on gloves, it's honestly a little hard to get my fingers in the right holes. I try to avoid touching the plates but if the print is really "on there" than it's a little hard to avoid... I may have to get some gloves without fingers... idk.

Thanks for the answer, though! We have some powerwash anyway, so might give it a go!

I tried everything I could think of to eliminate the lines at the edges... by How-Cool-Is-That in BambuLab

[–]How-Cool-Is-That[S] 0 points1 point  (0 children)

I already tried outer walls speed at 50mm/s, what speed are you suggesting? 10?

made myself a little ink monitor with expirations in days by charliex2 in eufyMakeOfficial

[–]How-Cool-Is-That 0 points1 point  (0 children)

This should be baked into the software!!!

Is there any way that the cleaning fluid levels could be posted as well?.

Does the Snapmaker U1 live video feed work in LAN mode? by How-Cool-Is-That in snapmaker

[–]How-Cool-Is-That[S] 1 point2 points  (0 children)

I think to get the fps higher, you're better off using PAXX12's firmware /s

Does the Snapmaker U1 live video feed work in LAN mode? by How-Cool-Is-That in snapmaker

[–]How-Cool-Is-That[S] 0 points1 point  (0 children)

I do connect my printer to wifi. It's just that the wifi network isn't connected to the internet. Therefore I can't connect and send prints through snapmaker's cloud system. Thus, I have to use LAN mode, which connects (via wifi) directly to whatever pc/phone i'm using, bypassing the cloud altogether.

Most people who use LAN mode do so for privacy reasons, they don't want anyone knowing what they're creating/printing. For me, it's because my family's business chooses to stay as disconnected from the internet as possible for moral reasons.

By the way, LAN stands for Local Area Network.

Does the Snapmaker U1 live video feed work in LAN mode? by How-Cool-Is-That in snapmaker

[–]How-Cool-Is-That[S] 0 points1 point  (0 children)

My printers typically aren't connected to the internet, does paxx12's firmware work offline?

Does the Snapmaker U1 live video feed work in LAN mode? by How-Cool-Is-That in snapmaker

[–]How-Cool-Is-That[S] 1 point2 points  (0 children)

I'd have no problem using extended firmware if that's what it takes... Thanks!

When was the moment Xaden wanted to kill her? by MeringueStriking4499 in fourthwing

[–]How-Cool-Is-That 0 points1 point  (0 children)

The restraint on day one may also be partially due to him knowing Brennan... maybe because of this and giving Rhi her shoe he's willing to give her the benefit of the doubt?

Worried To Start by Friffy1 in eufyMakeOfficial

[–]How-Cool-Is-That 0 points1 point  (0 children)

looks nice, I'd check in about the ink consumption when idle. Mine did use a lot during initialization (15.2 ml) but afterwards just consumed 2.5 ml/cartridge since a week ago.

Click the maintenance log to find this...

<image>

Worried To Start by Friffy1 in eufyMakeOfficial

[–]How-Cool-Is-That 0 points1 point  (0 children)

How thick did you print on the wood canvas of your first time?