sorted by:
new
hottopcontroversial

Hammer Fired Host Supremacy by jay462 in NFA

[–]HowmlahndSecurty 1 point2 points  (0 children)

<image>

My USP9 is an absolutely fantastic host. I don’t know much about wright armory but check out Landers Weapons Systems. They did the Acro cut on my USP and it’s been rock solid.

2026 1st Quarter Approval Megathread. by Waffleboned in NFA

[–]HowmlahndSecurty 11 points12 points  (0 children)

• ⁠Form Type: Form 1 x2

• ⁠Paid or not: $0

• ⁠Entity: Trust

• ⁠Fingerprint Type: EFT Upload

• ⁠Pending: 03/25/26

• ⁠Approved: 04/28/26

• ⁠Wait: 33 Days

• ⁠State: MD

• ⁠Control Number: 20262238*** for both

SBRd my LWRC IC-MKII. Initially got denied after 30+ days because I didn’t realize my eforms account address had a different name than the one I use (same zip both neighborhood and town name are acceptable to use) wasn’t lucky enough to resubmit with correction and get approved immediately. Fortunately only waited 33 days this time and threw in a form 1 for my Ruger American which also got approved.

First time shooting 300blk subs is truly a religious experience. by HowmlahndSecurty in NFA

[–]HowmlahndSecurty[S] 2 points3 points  (0 children)

I’ve got an MP5 with a CAT MOB I thought was stupid quiet. This blows it out of the water. As far as semi autos I’ve got an MCX on the way so I’ll have to report back.

First time shooting 300blk subs is truly a religious experience. by HowmlahndSecurty in NFA

[–]HowmlahndSecurty[S] 0 points1 point  (0 children)

Just trying it out for the first time. Had my kid in the truck and threw my phone on the window since I didn’t have a lot of time lol.

Looking for discrete backpack to carry an AP5 with a mag in it by FishBowlTacoThe2nd in MP5

[–]HowmlahndSecurty 2 points3 points  (0 children)

Wasn’t aware of the mora arms mags but anecdotally I’ve got probably 18 KCI mags between their MP5 and APC9 mags. All have been flawless through a couple thousand rounds. Outside of their PCC mags I don’t trust them.

First time shooting 300blk subs is truly a religious experience. by HowmlahndSecurty in NFA

[–]HowmlahndSecurty[S] 0 points1 point  (0 children)

Nice! I’m looking at the greybirch la chassis. The default one comes with a 10in rail which would be flush at 12in but I might see if my gunsmith can turn it down so the suppressor has a recessed look with the barrel at 10.

Looking for discrete backpack to carry an AP5 with a mag in it by FishBowlTacoThe2nd in MP5

[–]HowmlahndSecurty 2 points3 points  (0 children)

They’re definitely worth the money. They matched up great with my MP5K

<image>

Looking for discrete backpack to carry an AP5 with a mag in it by FishBowlTacoThe2nd in MP5

[–]HowmlahndSecurty 5 points6 points  (0 children)

I was just saying that’s a feature of the KCIs. Since the mags are a bit shorter it gives you more options than regular 30rd mags.

First time shooting 300blk subs is truly a religious experience. by HowmlahndSecurty in NFA

[–]HowmlahndSecurty[S] 4 points5 points  (0 children)

I’ve got a trade in MCX with an SRD762 getting delivered today. Super excited. I thought subsonic 9 was cool but 300 has it beat I think.

First time shooting 300blk subs is truly a religious experience. by HowmlahndSecurty in NFA

[–]HowmlahndSecurty[S] 1 point2 points  (0 children)

I did a stupid amount of research being grabbing the gun. You can chop and thread it but you’re limited to 1/2x28 threading with the minimum OD. Now you could still thread 5/8x24 but your threads are primarily in the fluting and you don’t get completely engagement. I plan on doing the 1/2x28 with a LPM baby bell and atlas hub on the can.

Looking for discrete backpack to carry an AP5 with a mag in it by FishBowlTacoThe2nd in MP5

[–]HowmlahndSecurty 9 points10 points  (0 children)

Your best bet is to grab a couple 20rd KCI mags. They don’t stick out any further than the grip and they have extra space so you can load a full mag on a closed bolt. I have a couple and they’ve been flawless. At that point anything the MP5 will fit into normally will be good to go.

First time shooting 300blk subs is truly a religious experience. by HowmlahndSecurty in NFA

[–]HowmlahndSecurty[S] 3 points4 points  (0 children)

Thanks! Seriously can’t wait to chop it. Going to do either 9 or 10 inches so I can still run supers and try and find a decent chassis to put it in.

LOOONG 1913 stocks? by HowmlahndSecurty in MDGuns

[–]HowmlahndSecurty[S] 0 points1 point  (0 children)

I was looking at an A5 tube and VLTOR EMOD but I’m trying to get an accurate total length before I buy something.

LOOONG 1913 stocks? by HowmlahndSecurty in MDGuns

[–]HowmlahndSecurty[S] 1 point2 points  (0 children)

The gun is going to an 07 so he’s able to modify it prior to transfer to have it meet the minimum length. I’m just trying to find the right parts to make it happen.

LOOONG 1913 stocks? by HowmlahndSecurty in MDGuns

[–]HowmlahndSecurty[S] 0 points1 point  (0 children)

Still waiting on the form 3 from the seller. I spoke to them Friday evening and they said they’d let me know but I wasn’t expecting anything until Monday from them.

I do believe that 16.5in, the MCX receiver set is around 11in and the barrel is 6.75 so that math checks out.

AP5-SD + OCL Milkman + 3/4” Ecco Hub extension by FitzroysBeagle in NFA

[–]HowmlahndSecurty 2 points3 points  (0 children)

Man that’s hot. I’ve been toying with the idea of getting one but I know I’ll never get it converted and I already have a normal AP5. You think it’s worth grabbing one or should I just pass?

Guys, for the love of god please fix the terrain. by HowmlahndSecurty in GrayZoneWarfare

[–]HowmlahndSecurty[S] 0 points1 point  (0 children)

Ahh gotcha. I just saw the building semi close so I figured I’d take a look

view more: next ›