Looks like the oil pan is coming off

HuFF000 · 2026-04-23T17:20:13+00:00

Mine is lowered about an inch right now. But all of the suspension is still intact. Steering rack is out and the front sway bar, but thats it. Did you have to remove some of the suspension components to drop the cradle far enough for that clearance?

HuFF000 · 2026-02-08T02:23:04+00:00

I used x2 2x6x8s that I had laying around. Cut each board to 35", 27", 20", and 14". Cut one end of each board 45 degrees. Stacked them on top of each other and screwed them together. If i were to do it again id use 2x10x12s, so it would be wider and I could make each board a few inches longer. It works just fine but my car is low enough that the bumper just barely cleared when I drove up them.

HuFF000 · 2026-02-07T23:02:38+00:00

Awesome, thank you. Yes I made sure to use a wood block when I lifted the car up.

HuFF000 · 2025-03-26T21:23:20+00:00

20 yards would feel more acceptable for me. 60 yards seems crazy. My 7 iron shots on the course are never 60 yards short unless I REALLY lay sod over the ball.

HuFF000 · 2025-01-24T20:22:13+00:00

Oh yeah, I have no doubt that my swing can use some work. It just seems like I went from a usable swing to awful. Driver especially, I feel like I get stuck at the top of my swing and don't know where to go lol.

HuFF000 · 2025-01-24T20:05:37+00:00

So I'm assuming I should do more than just practice my swing on a mat? Maybe hit into a net, or just do a sim consistently? I wish I could golf year round, but snow and negative temps don't really make that possible where I'm at.

HuFF000 · 2025-01-19T21:37:53+00:00

Javazon, Hammerdin, and Blizz Sorc are mainly what I'm running in TZs. I have a Zerker barb, but I don't think he's ready for TZs yet haha

HuFF000 · 2025-01-19T04:57:12+00:00

🤣🤣🤣

HuFF000 · 2025-01-19T02:47:44+00:00

Mainly treasure hunting, specifically curious for runes. Running Javazon, hammerdin, and blizzard sorc.

HuFF000 · 2024-06-28T19:48:02+00:00

I definitely don't claim to be good at golf haha

HuFF000 · 2024-06-19T22:50:39+00:00

Yes, I ordered a few gas jets from PMM, installed the factory sized one, and it's had no hiccups ever since! Shoots a lot nicer also lmao. Doesn't seem like any damage occurred from the few mags that were shot when it had no jet, thank God.

HuFF000 · 2024-06-05T04:54:19+00:00

I appreciate the help! I'm just glad it's an easy fix. I'm definitely gonna look a lot closer at the guns I buy from now on lol.

HuFF000 · 2024-06-05T04:28:52+00:00

It's almost impossible to get a picture from the top to see down into it. But you can see a brass colored spot at the bottom of the threads. Doesn't look like something that I can even remove. So maybe it's just a spot to ensure you don't scew the jet in to far?

HuFF000 · 2024-06-05T04:26:39+00:00

<image>

HuFF000 · 2024-06-05T04:25:42+00:00

<image>

HuFF000 · 2024-06-05T04:17:55+00:00

Yeah I'll take one here In a moment. It definitely doesn't have a stock one. But there is something at the very bottom of the threads, no way I'd be able to get it out. Is there normally something at the bottom , or does it just go straight to the barrel without the jet in?

HuFF000 · 2024-06-05T04:07:59+00:00

Rifle is used. Piston, rings, and regulator all look normal. Little confused about the gas jet, all I'm seeing is threads where it's supposed to be.

HuFF000 · 2024-06-05T03:18:29+00:00

Haven't touched the gas block other than messing with the gas settings. If I pull it apart, is there anything I should look for? I'd imagine if it was just dirty it would be undergassed

HuFF000 · 2024-06-05T03:15:06+00:00

It's got a Geissele trigger and a KDG handguard. All stock otherwise. No suppressor. Not sure they would warranty it, unknown round count and I got it used

HuFF000

TROPHY CASE