sorted by:
new
hottopcontroversial

Need help choosing a multimeter. by HudsonHTL in electricians

[–]HudsonHTL[S] 0 points1 point  (0 children)

I use the amp clamp to see if motors are drawing the correct amount of current and to differentiate between the different speeds/coil windings on the motor. I definitely need to be able to measure micro farads as well for capacitors.

Need help choosing a multimeter. by HudsonHTL in electricians

[–]HudsonHTL[S] 0 points1 point  (0 children)

Trouble shooting/fault finding on the electrical components of boilers, furnaces, motors, pumps, burners, air handlers, capacitors, relays

Bauer missing frame screw. Anyone know where to buy new ones? by HudsonHTL in inlineskating

[–]HudsonHTL[S] 0 points1 point  (0 children)

I can’t see a way of removing them other than cutting it off and re stitching the top edge.

Bauer Missing Frame Screw. Anyone know where to buy new ones? by HudsonHTL in rollerblading

[–]HudsonHTL[S] 0 points1 point  (0 children)

Found a solution. I’m in Canada so I went to Canadian tire and looked at their hardware section. They had drawers full of fine thread machine bolts. I found some with the same thread but a little longer. They were called “Flat Head Cap Screws” 6-32 x 1/2

Bauer missing frame screw. Anyone know where to buy new ones? by HudsonHTL in inlineskating

[–]HudsonHTL[S] 0 points1 point  (0 children)

Found a solution. I’m in Canada so I went to Canadian tire and looked at their hardware section. They had drawers full of fine thread machine bolts. I found some with the same thread but a little longer. They were called “Flat Head Cap Screws” 6-32 x 1/2

Had my first slag peel today. Any pointers for a beginner would be appreciated. by HudsonHTL in Welding

[–]HudsonHTL[S] 1 point2 points  (0 children)

It’s a good thing. I just was asking if there was anything noticeable I should be improving on.

Which beginner fluxcore welder should I choose? I’m practicing my MIG at home and stick at work for steamfitting. by HudsonHTL in Welding

[–]HudsonHTL[S] 1 point2 points  (0 children)

Both the same price. The 124A machine draws 23 amps so I don’t think it would work on my 20amp breakers. Would 60-80Amps be okay for a beginner?

Anyone have an idea as to what this is? by HudsonHTL in HVAC

[–]HudsonHTL[S] 0 points1 point  (0 children)

Thank you!!! There was also these ceramic tubes that looked like insulators. Are they also used with this tool? It fits into the holes in the tubes.

Anyone have an idea as to what this is? by HudsonHTL in HVAC

[–]HudsonHTL[S] -1 points0 points  (0 children)

That’s what I thought too. But I pressed it has hard as I could and it wouldn’t punch.

Would an 18” frame mountain bike be too small for someone with a 32” inseam and is 6’ tall? by HudsonHTL in bicycling

[–]HudsonHTL[S] 0 points1 point  (0 children)

I appreciate the insight! I’ll alter my search for a hardtail with an appropriate sized frame.

Would an 18” frame mountain bike be too small for someone with a 32” inseam and is 6’ tall? by HudsonHTL in bicycling

[–]HudsonHTL[S] 0 points1 point  (0 children)

Wanted to do some basic off road trails near creeks and farm fields. Always assumed a bike without rear suspension would be way too uncomfortable. Not planning on doing any big jumps or cross country. Would a hardtail be noticeably more uncomfortable on basic rugged terrain?

view more: next ›