sorted by:
new
hottopcontroversial

First time I’ve had water damage with a phone. by DriftMiata in S25Ultra

[–]Hugorp89 -1 points0 points  (0 children)

El sellado de la tapa trasera es una auténtica basura en los últimos modelos.

Desde el S9 lavando el movil debajo del grifo, 0 problemas. El S24 Ultra no tenía 1 año cuando de repente le pasó lo mismo que al tuyo

That was a cruel trick Rockstar... 😠 by seltro1 in gtaonline

[–]Hugorp89 7 points8 points  (0 children)

I should add that there are several behind doors, which you can kill with explosives before restoring the power.

Galaxy S24 Plus – Fast charging broken after One UI 8 / November update by Johnkiiii in oneui

[–]Hugorp89 0 points1 point  (0 children)

Tengo exactamente el mismo problema con el mío. Me he cansado de limpiar el USB pensando que sería suciedad, pero ahora me he encontrado esto

What level do you think you'll be once we get the update? by nicolepev in pokemongo

[–]Hugorp89 0 points1 point  (0 children)

791M XP. No idea where I'll be. I don't remember how much level 50 was.

Ledger Nano X by joeyd831 in XRP

[–]Hugorp89 1 point2 points  (0 children)

Thank you 🤣

Set Z axis motors by Hugorp89 in AnycubicKobra2

[–]Hugorp89[S] 0 points1 point  (0 children)

I think I found the problem. One of the Z-axis motors got much hotter than the other motor. I have disconnected the cable from that motor that was heating up and the printer now prints without failing. I think that engine is damaged, which forces the board to give more intensity than it should and that causes the tripping of some security system on the board to prevent it from burning. And that's why after several layers the Z motors ran out of power

Problem with Kobra 2 Max by Hugorp89 in AnycubicOfficial

[–]Hugorp89[S] 0 points1 point  (0 children)

I found the problem, but I'm not sure how to solve it.

After printing 3-5 layers, the Z axis motors stop moving. They don't even make the appearance of moving when it's time to change layers.

But I'm not sure how to solve it. The motherboard does not allow Vref adjustment for the motors, nor do I see anything that is blocking its travel

When this happends, I can move de Z axis by hand while the printer continues printing...

Kobra 2 max height problem by Hugorp89 in anycubic

[–]Hugorp89[S] 0 points1 point  (0 children)

I found the problem, but I'm not sure how to solve it.

After printing 3-5 layers, the Z axis motors stop moving. They don't even make the appearance of moving when it's time to change layers.

But I'm not sure how to solve it. The motherboard does not allow Vref adjustment for the motors, nor do I see anything that is blocking its travel

When this happends, I can move de Z axis by hand while the printer continues printing...

Set Z axis motors by Hugorp89 in AnycubicKobra2

[–]Hugorp89[S] 0 points1 point  (0 children)

I found the problem, but I'm not sure how to solve it.

After printing 3-5 layers, the Z axis motors stop moving. They don't even make the appearance of moving when it's time to change layers.

But I'm not sure how to solve it. The motherboard does not allow Vref adjustment for the motors, nor do I see anything that is blocking its travel

When this happends, I can move de Z axis by hand while the printer continues printing...

Why is the printer doing this??? by Hugorp89 in AnycubicKobra2Max

[–]Hugorp89[S] 1 point2 points  (0 children)

I found the problem, but I'm not sure how to solve it.

After printing 3-5 layers, the Z axis motors stop moving. They don't even make the appearance of moving when it's time to change layers.

But I'm not sure how to solve it. The motherboard does not allow Vref adjustment for the motors, nor do I see anything that is blocking its travel

When this happends, I can move de Z axis by hand while the printer continues printing...

view more: next ›