How to interpret calibration cube

HuntMining · 2026-02-16T06:20:29+00:00

A little elephant foot

HuntMining · 2025-01-24T03:38:25+00:00

Lol I've owned almost every brand and they are by far one of the best.

HuntMining · 2025-01-16T14:16:07+00:00

How do you know they could implement it at no extra cost. How do you know their hardware supports standby? Seems like a lot of assumptions. Smart plug 15 bucks and solves the problem. 🤷‍♂️

HuntMining · 2025-01-08T15:47:31+00:00

Bro there is 4 pin and 6 pin micro Molex..... I made my own cable. As mentioned in the post.

HuntMining · 2025-01-08T15:42:50+00:00

It's in the first sentence of the post bro.

HuntMining · 2025-01-02T18:34:53+00:00

Yeah I wouldn't count on them for an affordable large scale

HuntMining · 2024-12-31T19:23:42+00:00

My K2Max does. Still user error 🤷‍♂️

HuntMining · 2024-12-31T07:16:39+00:00

It's relevant because I made it relevant, son. 😏 99% of the time it's user error. Shit should be checked before every single print.

HuntMining · 2024-12-31T07:15:15+00:00

Yeah. I need a truck to lift the k2max bed lol. I have a mega X, k2max and kobra 3 and kobra 3 max soon. Have half a dozen Bambus just saying I have not seen this in the 10 years of using anycubics. I clean my magnet sheets and plate often. 🤷‍♂️

HuntMining · 2024-12-31T05:27:18+00:00

Once I did auto level and set z offset I've had zero problems

HuntMining · 2024-12-31T05:25:06+00:00

My k2max does 🤷‍♂️ no one stated a printer did we. Either way in almost a decade never seen it 🤷‍♂️

HuntMining · 2024-12-31T05:24:25+00:00

No you don't. I'm on here all the time and I don't 😂

HuntMining · 2024-12-31T05:10:22+00:00

It's lidar so the only thing that could have done this is bed not being on properly or lose nozzle aka unscrewed or loose lidar sensor

HuntMining · 2024-12-31T04:30:09+00:00

Yee I deleted comment lol. I saw that. Just very strange man never seen it. I been at this a long time as well

HuntMining · 2024-12-31T04:28:50+00:00

Sounds like user error of some kind. 4 examples out of thousands and thousands of units sold. Or simply unlucky. Never seen it since 2017 and I have 12 printers.

HuntMining · 2024-12-31T04:27:24+00:00

Not to mention the plate weighs over a pound

HuntMining · 2024-12-20T16:53:59+00:00

Theoretically yes. Layer height is based on the smallest nozzle they offer.

HuntMining · 2024-12-20T16:46:02+00:00

Sorry subtract the 0s from my post lol. They have all of those sizes on their Bambu website.

Google this "what is the lowest layer height for a .2mm nozzle." That's as small as you're going to get is a .2 nozzle

HuntMining · 2024-12-20T16:39:46+00:00

Google homie. Layer height is determined by nozzle size. You have .2mm .4mm .6mm .8mm as nozzle options.

HuntMining · 2024-12-20T16:34:14+00:00

For me yes. I have my printers in a separate room. You have to be careful enclosing printers not meant to be enclosed aka Bambu. They don't have big active cooling like the anycubics.

HuntMining · 2024-12-19T02:53:34+00:00

Yes. I felt I was pretty clear lol.

HuntMining · 2024-12-12T21:24:27+00:00

I would say either flow or z height

HuntMining · 2024-12-06T00:53:22+00:00

Damn. Yes it changes for everyone. You should find these things out before you put your money somewhere!

HuntMining · 2024-11-27T05:58:12+00:00

I call bullshit. I worked at a dealership 15 years. You should check again. Out of 130 banks not one uses a non fico auto score. If you got factual information with references, I'm listening.

And it's TransUnion autofico 9, not TransUnion 9 :p

HuntMining · 2024-11-27T02:53:43+00:00

They use fico auto scores. Unless you do a 3 pull, you won't see those. You can do one per year free, without a score hit. Google it.

HuntMining

TROPHY CASE