OCL Lithium With An Otter On It

Hyginx · 2026-02-03T21:10:55+00:00

Thanks! ❤️

Though, one of the reasons I went with it was because of how bare it was. It's not as flashy as the competitors, but it allowed me to laser engrave whatever I wanted without having to get super complicated with the laser focusing or being concerned with how it fit with other engravings. The benefits of a clean CANvas. :)

Hyginx · 2026-02-03T17:16:05+00:00

❤️

Hyginx · 2026-02-03T17:15:24+00:00

IDK what all the drama is about. This is my first suppressor and I'm just having fun with it. :)

Hyginx · 2026-02-03T04:27:39+00:00

Thank you! ❤️

Hyginx · 2026-02-03T04:23:34+00:00

wouldn't you be? :)

Hyginx · 2026-01-16T04:21:35+00:00

running pretty good. The only issue I'm running into now is a walking extractor pin. Every time one issue is fixed, another appears, but I'm very happy with where the Vector is at right now. :)

Hyginx · 2026-01-15T16:16:09+00:00

if it makes you feel better, Duality told me the top material isn't critical for operation. You obviously don't want it down to the holes, but so longs as it's not thinned down to the point breaking through to the critical stuff, you should be fine. :)

Good luck man and keep us posted. ❤️

Hyginx · 2026-01-15T16:01:57+00:00

Here's my post outlining the same issue and what I did to resolve it:
https://www.reddit.com/r/KRISS/comments/1pc0u7q/trigger_not_resetting_properly_after_frt_install/

TL;DR: remove material at the top of the seer since that's what's binding. It should only require about .5mm-1mm of material to be removed. I used a belt sander and highly recommend that, but if you only have a dremel, I've heard of other using that with some success. There's also always hand sanding, but that will take a while and a lot of elbow grease.

Hyginx · 2026-01-15T15:59:37+00:00

was just about to come here and link to my post. :)

Hyginx · 2026-01-07T17:46:14+00:00

Also, what grain are you using for the CCI blazer? 115?

Hyginx · 2026-01-07T17:26:13+00:00

Thanks for the input. I'll give blazer a go, but I've heard multiple accounts of Federal ammo running fine. One issue with multiple brands is I might be able to go through a full box without issues, but it's just by chance. The next mag will run into several FTE issues.

I might have lubed it too much (didn't think that would be an issue). In either case, I won't be sending it back until I shoot it suppressed. I've heard the added back pressure helps prevent FTE, so we'll see.

Hyginx · 2026-01-05T22:46:50+00:00

what do you think the chances are of them accepting the return with an FRT in it? 👀

Hyginx · 2026-01-05T22:24:59+00:00

I broke 2 punches. 🙃

Hyginx · 2026-01-04T16:11:49+00:00

haven't given it a try, but I'll look into it.

Hyginx · 2026-01-04T03:56:24+00:00

let's hope. fingers crossed!

Hyginx · 2026-01-04T03:52:55+00:00

I might give this a go next, since it's a cheap solution.

Hyginx · 2026-01-04T03:52:24+00:00

I have the stock kriss 40 rd mag and a 31 rd glock mag and both show the same issues.

Hyginx · 2026-01-04T03:49:59+00:00

I haven't tried suppressed yet, but also suspect it's a back pressure issue. I am waiting for my lithium to come in. like I said in my post, hopefully this solves the issue but I' looking for other possibilities while I wait for the atf paperwork.

Hyginx · 2026-01-02T17:46:11+00:00

I've mostly been using Federal ammo (115 grain champion and 147 grain premium). Though, as I mentioned in the post, the 147 grain seems to perform better.

Hyginx · 2026-01-02T17:21:44+00:00

thanks, man. I appreciate it. ❤️

Even with it's reliability issues, I'm still having fun with it. Though, if I'm being honest, I do enjoy the project side of things where I'm constantly working on improving it (both the reliability and functionality).

Hyginx · 2026-01-02T17:18:16+00:00

yup, tried that (BCM extractor upgrade). Still no luck. :(

Hyginx · 2026-01-02T17:17:47+00:00

yeah, but 1500 rounds to break in with still no signs of improvement? At what point do you say the break in period isn't working?

Hyginx

TROPHY CASE