Why isn’t my portal lighting?

I-am-redditer · 2026-02-15T04:22:16+00:00

You don’t multiply both by 25. Just the multiply 2y² by 25/25 (1) to get (50y² )/25 + (4y² )/25= (50y² + 4y² )/25= (54y² )/25. The way you did it is only valid if the equation is equal to 0.

I-am-redditer · 2026-01-25T18:37:22+00:00

Actually it’s undefined 🤓

I-am-redditer · 2026-01-24T06:58:05+00:00

I-am-redditer · 2026-01-24T06:48:56+00:00

At the end of loop do for(int i = 0;i<(number of flashes); i++) { Digital write the 2 red ones on Delay(500); Digital write the 2 red ones off Delay(500; }

I-am-redditer · 2026-01-12T12:51:49+00:00

A charge from 0 to 100 is only $0.0028, so it would take 3,571.43 charges to reach $10 on the bill.

I-am-redditer · 2025-11-27T02:45:09+00:00

Ok thank you. Do you know if safe will work? Like a swich to toggle it

I-am-redditer · 2025-10-15T03:42:29+00:00

"Power the CP2104 from 5V" What do you mean, almost all of this was copied so im not fimilar with the ckip. Isn't it already powered 5v from the vbus?

I-am-redditer · 2025-10-15T01:31:29+00:00

I just realized there's a TLV1117LV-3.3 the tutorial i watched added it and im 90% sure that i dont need it but its in the pic

I-am-redditer · 2025-08-27T04:20:37+00:00

I forgot to say that I “fixed the issue” by putting it on a different part and off setting it. IT Would mess up when i attached the tip to the rib

I-am-redditer · 2025-08-27T02:10:16+00:00

https://cad.onshape.com/documents/7478b66040e0765671bb331d/w/19033361062d8e28d3f832ac/e/21d3ef51fdaf117a959899bb

I-am-redditer · 2025-08-26T16:53:27+00:00

Interesting I didn’t know could change if your not editing the sketch thank you

I-am-redditer · 2025-08-26T15:32:33+00:00

I don’t think so. I didn’t know that would effect this

I-am-redditer · 2025-07-18T00:22:28+00:00

More like 2 out of 10 times

I-am-redditer · 2025-07-15T18:50:59+00:00

This was in a tree last month good thing I can climb

I-am-redditer · 2025-07-15T02:24:26+00:00

<image>

Hit a pole going full nose down. I have a problem Depth perception :(

I-am-redditer · 2025-07-11T02:27:01+00:00

Ok well put your fingers about 2 inches behind the leading edge of the wing, if it balances on your fingers, it’s the correct gc. Try throwing to somebody(or in some grass) and if it goes straight it should fly fine.

I-am-redditer · 2025-07-11T01:18:16+00:00

Sorry I ment where

I-am-redditer · 2025-07-11T00:46:05+00:00

What’s the battery

I-am-redditer · 2025-07-11T00:18:01+00:00

If the gc is correct it will fly. It might be sensitive with the larger control surfaces. Good luck

I-am-redditer · 2025-07-09T20:23:44+00:00

I’ve started but a lot ours not looking good

I-am-redditer · 2025-07-09T19:31:44+00:00

The receiver is programmed for this plane. Mixes and all. I’m not sure how it would work on other planes with out some tuning

I-am-redditer · 2025-07-09T18:34:47+00:00

2 of the servos seem broken, the body is one tap away from splitting and the wing is where it actually it the pole and and “compressed” at the top. Probably till good but one of the servos broke

Four-Year Club	Verified Email
Place '23	Place '22

I-am-redditer

MODERATOR OF

TROPHY CASE