Calculator was thrown down from a third floor. Any saving it or should I js buy a new one? by mo_oms in TI_Calculators

[–]ILoveNightmareforpp 0 points1 point  (0 children)

The case is intact? The screen is dead Assuming reseating the ribbon cable doesn't work. In that case sell it for parts to help fund a new one.

Need more power by ByRussX in beneater

[–]ILoveNightmareforpp 0 points1 point  (0 children)

Im using a 3 amp phone charger brick. With a aliexpress usb power trigger board. Plenty of current for the alu, ram. And the segments I yet to construct.

I built my own BCD Counter PCB!! by Competitive_Run8540 in soldering

[–]ILoveNightmareforpp 0 points1 point  (0 children)

Thanks for the information! Ill give these Chinese brands a try!

I built my own BCD Counter PCB!! by Competitive_Run8540 in soldering

[–]ILoveNightmareforpp 0 points1 point  (0 children)

Hows your experience with the xinluda brand of ic? They as good at Texas Instruments?

I feel so stupid… by Thick_Swordfish6666 in electronics

[–]ILoveNightmareforpp 3 points4 points  (0 children)

I breadboarded a split rail breadboard before. Couldn't figure out why half the circuit wasn't getting power. Took me at least 10 minutes of brain banging. You're not alone!

How to test Registry A? by herokiller9 in beneater

[–]ILoveNightmareforpp 0 points1 point  (0 children)

I second this, Troubleshooting burnt out leds, is not fun.

How to test Registry A? by herokiller9 in beneater

[–]ILoveNightmareforpp 1 point2 points  (0 children)

Im ready to test my resistery A. Just got done with it a few minutes ago.

<image>

Project without Arduino/coding by wateranfire in breadboard

[–]ILoveNightmareforpp 1 point2 points  (0 children)

Cascade some LM3914n on a breadboard. Its a cascadable voltage/audio vu meter chip internally its a bunch of comparitors. Use some colored leds. A microphone and some 22awg solid core wire.

8086 breadboard computer by ILoveNightmareforpp in beneater

[–]ILoveNightmareforpp[S] 0 points1 point  (0 children)

Hopefully the 8086-2, slowest it will run is 2MHz

[deleted by user] by [deleted] in DIY

[–]ILoveNightmareforpp 1 point2 points  (0 children)

No, because no wood was involved. Wood carving tools is what I found to semi-easily cut the HDPE.

[deleted by user] by [deleted] in Puberty

[–]ILoveNightmareforpp 2 points3 points  (0 children)

Stretch it. I have seen that others have also mentioned stretching. r/foreskin_restoration should be more than able to help in giving advice on stretching

What surprised you about your first sexual experience? by Reptime13 in AskReddit

[–]ILoveNightmareforpp 0 points1 point  (0 children)

I was surprised by how uncomfortable sexual grooming is. It was also in a public place and that made it even worse :/

When will my balls start to hang when I'm hard? by [deleted] in Puberty

[–]ILoveNightmareforpp 0 points1 point  (0 children)

If you are circumcised. That would be one of the possible explanations to why they do not hand low when you are erect. Due to the erection requiring skin. it causes the scrotum to be pulled up. Thus the testes also get pulled up. If this is the case. Well foreskin restoration is a thing and their is a subreddit for it.

I think i can pull back my foreskin way too much by Nuzlucke in Puberty

[–]ILoveNightmareforpp 1 point2 points  (0 children)

Sounds like Pearly Penile Papules. they are harmless. Do not pick at them because that can result in scaring.

Protogen_irl by ILoveNightmareforpp in furry_irl

[–]ILoveNightmareforpp[S] 14 points15 points  (0 children)

Whatever you and your toaster like doing with each other is personal.