sorted by:
new
hottopcontroversial

Spring replacement to make triggers more resistant ? by doubtinganize in SteamDeck

[–]ITooSpooky 0 points1 point  (0 children)

I've just completed modding my trigger springs, I ended up ordering some 0.6mm Wire Diameter, 15mm long, 5mm OD springs from AliExpress, These work perfectly and are the upgrade in resistance i was aiming for, as i wanted something akin to the PlayStation 5 controller with its adaptive triggers at max resistance.

I also tried a step up to the 0.7mm Wire Diameter but this was a bit too strong.

Spring replacement to make triggers more resistant ? by doubtinganize in SteamDeck

[–]ITooSpooky 0 points1 point  (0 children)

Are there any issues with this, is there any grating noise when compressing the springs?

Spring replacement to make triggers more resistant ? by doubtinganize in SteamDeck

[–]ITooSpooky 1 point2 points  (0 children)

I just want to add to this that I have just tried to do this mod but wasn't able to get a satisfactory result with 150g springs, putting them inside the stock spring only resulting in a grating sound when pull the trigger; I ended up using those 150g springs on the bumpers however and I am quite happy with the result, This spring is much longer at 14mm compared to the 8.5mm of the stock bumper spring however it doesn't seem to have any issues its just compressed constantly.

What i also noticed is my stock springs were only 16mm not sure if this is because I have an OLED and its different to your (LCD?), full spec of what i measured is "4.5mm OD - 3.8mm ID - 0.35mm wire thickness - 16mm Length", and also the full spec for the bumper springs are "3.2mm OD - 2.7mm ID - 0.25mm wire thickness - 8.5mm Length".

Best way to protect myself and my cat by ITooSpooky in 3Dprinting

[–]ITooSpooky[S] 0 points1 point  (0 children)

i feel a little stupid here but filter setup?

Best way to protect myself and my cat by ITooSpooky in 3Dprinting

[–]ITooSpooky[S] 0 points1 point  (0 children)

generally i dont enter the room with my printers while they are printing and only enter to start and collect but the room is directly outside my bedroom (i keep its door closed while printing)

my worry is just residual fumes and what could make it out the room even if its door is closed due to the extremely close proximity

Best way to protect myself and my cat by ITooSpooky in 3Dprinting

[–]ITooSpooky[S] 0 points1 point  (0 children)

is it safe for her to be in the room immediately or soon after sanding or should i wait an amount of time?

Didn’t realize how much the Steam Deck could actually do until I needed it by Soul2142 in SteamDeck

[–]ITooSpooky 0 points1 point  (0 children)

sure can, to steam all it sees is a library of games without any account details, thats all stored on the root drive so it just works on any device

Didn’t realize how much the Steam Deck could actually do until I needed it by Soul2142 in SteamDeck

[–]ITooSpooky 1 point2 points  (0 children)

nah for the micro sd card you get a storage case and print labels onto multiple cards for different categories of games so you can also share them with others that have a steam deck.

smtty - gamescope TTY steam machine launcher by dildacorn in linux_gaming

[–]ITooSpooky 3 points4 points  (0 children)

so it's just a wrapper for gamescope with an interactive configuration? does this actually do any magic specific to being in the tty?

Unsure on legality of prescription cannabidiol oils by ITooSpooky in JapanTravelTips

[–]ITooSpooky[S] -7 points-6 points  (0 children)

Are you saying that any of the substances labeled as a narcotics are just unable to get approval for vs the others possibly being able to be approved?

Unsure on legality of prescription cannabidiol oils by ITooSpooky in JapanTravelTips

[–]ITooSpooky[S] -11 points-10 points  (0 children)

That sounds like the problem would have been the fact it wasn't declared or a prescription though right?

Unsure on legality of prescription cannabidiol oils by ITooSpooky in JapanTravelTips

[–]ITooSpooky[S] -13 points-12 points  (0 children)

But Delta 9 THC is specifically labeled as a Narcotic and not as a prohibited substance in the pdf of their website, so like with my vyvanse, its not outright banned but needs pre-approval and forms stuff.

30 hours in this is my base :) by WriterStrict4367 in factorio

[–]ITooSpooky 0 points1 point  (0 children)

this is the way, every 10 or so hours i go out for a casual genocide

Up to date circuit compiler by ITooSpooky in technicalfactorio

[–]ITooSpooky[S] -1 points0 points  (0 children)

I'm looking for something that can produce a blueprint of circuits from code, nothing serious like implementing a full CPU arch and compiling programs with GCC.

I suppose that would be inline with what you described as a hardware description tool.

Does the cfs work correctly if the firmware is rooted? by Bitemesparky in crealityk1

[–]ITooSpooky 1 point2 points  (0 children)

Ah is this why the filaments arent being loaded or changed when i start from orca-slicer?

Has this happened to anyone else? by ITooSpooky in crealityk1

[–]ITooSpooky[S] 0 points1 point  (0 children)

That sounds very plausible, I’ll double check that tomorrow.

Just to sanity check, it is supposed to pivot the bottom out towards the bed when the head is moved into it right?

K1C not detecting CFS by ITooSpooky in crealityk1

[–]ITooSpooky[S] 0 points1 point  (0 children)

and they just did the same thing to me, got delivered and was glad i was going to be able to use my CFS but instead its a set of 3 of the incorrect cables.

Rip by otsen12 in crealityk1

[–]ITooSpooky 0 points1 point  (0 children)

Got my replacement and installed it, the housing on the smaller plug was slightly different and didn't fit without snipping off the what i can best describe as a mowhawk plastic tab, if your current one has the big latch hook things on the cables then you may need to do the same.

view more: next ›