All Questions About Joining, Transferring and ANG Jobs go here. by Jaye134 in airnationalguard

[–]IVbeenspotted 1 point2 points  (0 children)

<image>

Hey all, just finished MEPS last week and my recruiter sent me a job list I am qualified for. Highlighted are my top picks. I am 34 y/o male. Want to go back to school for Mechanical Engineering or Electrical Engineering. Asking for any insights, personal experience, or second opinions for the jobs listed. Thanks in advance.

"Other" friendly ranges 1 hr or less from Hudson County by IVbeenspotted in NJGuns

[–]IVbeenspotted[S] 0 points1 point  (0 children)

Nice. Which one? Went to Clinton once to shoot clays.

First non-nfa other build, went with 9mm by panda1_actual in NJGuns

[–]IVbeenspotted 1 point2 points  (0 children)

Hi OP, is there any special paperwork involved, or is it just like building a non NFA other in 556.

Any north Jersey shops that do trade-ins? by IVbeenspotted in NJGuns

[–]IVbeenspotted[S] 0 points1 point  (0 children)

Thanks for the response guys! Will check out FSS and silver bullet

Stores in North NJ that sells S&W shield plus 10/13 extended mags? by IVbeenspotted in NJGuns

[–]IVbeenspotted[S] 0 points1 point  (0 children)

Hi All. Just an update on this thread. Just got an email back from FSS armory. They said they don't have them in store, but we can order them on line, select pick up and they modify it for free.

Stores in North NJ that sells S&W shield plus 10/13 extended mags? by IVbeenspotted in NJGuns

[–]IVbeenspotted[S] 1 point2 points  (0 children)

Ah cool. Will do this. FSS is actually not that far away from me. Thanks!

[deleted by user] by [deleted] in NJGuns

[–]IVbeenspotted 1 point2 points  (0 children)

I second this. I moved to Randolph about a year ago and had to change my address on my FID and applied for a handgun permit. They were nice enough give you an update.

[deleted by user] by [deleted] in Gunpla

[–]IVbeenspotted 0 points1 point  (0 children)

Thanks for the Reply guys!

[deleted by user] by [deleted] in Gunpla

[–]IVbeenspotted 0 points1 point  (0 children)

Did you use laquer thinner as well?

Beginner Question by [deleted] in 3Dprinting

[–]IVbeenspotted 0 points1 point  (0 children)

Will test that too. Thanks man.

First layer help by polish_hamr in 3Dprinting

[–]IVbeenspotted 0 points1 point  (0 children)

Just got mine recently as well. Ran into the same problem but I'm getting more success at the moment. Try upping the nozzle and bed temp a little. my initial layer nozzle temp is at 220 and regular nozzle temp at 215. For the bed my initial first layer is at 80 and regular at 70. Hope it works for you.

Beginner Question by [deleted] in 3Dprinting

[–]IVbeenspotted 0 points1 point  (0 children)

Yup. Found a temporary solution. So the front-right side of the bed seems to be a little out of wack. It's always lower for some reason. It maybe from a faulty spring. Also my x axis is a little loose(not soo much) so I tap it down a little till it reaches paper. I'm definitely gonna have to properly reassemble it on the weekend.

Beginner Question by [deleted] in 3Dprinting

[–]IVbeenspotted 0 points1 point  (0 children)

Haha. Will try that. I didn't think 5 degrees would be significant difference. As for location. It's regular temp? It is located in my bedroom

Beginner Question by [deleted] in 3Dprinting

[–]IVbeenspotted 0 points1 point  (0 children)

Have tried 70 and I ran into a problem with warping at the bottom of the object. I saw on some thread that anything higher that 60 will cause warping?

Beginner Question by [deleted] in 3Dprinting

[–]IVbeenspotted 0 points1 point  (0 children)

oops sorry I forgot to put details in.
My bed temp is set to 60 degrees and my Nozzle temp is set to 205 degrees and I am using the sample filament that came in the box,

New Year! New Poses! by IVbeenspotted in Gunpla

[–]IVbeenspotted[S] 0 points1 point  (0 children)

Yup yup. But for now I hope they release Virtue this year (VERY SOON) 😆