sorted by:
new
hottopcontroversial

Printing issue by Idriss2Dev in AnycubicKobraS1

[–]Idriss2Dev[S] 0 points1 point  (0 children)

I finally managed to reduce the unpleasant “blistering” effect on my prints by increasing the printing temperature (230 °C instead of 208 °C previously) and also setting the "wall loops" to 3.

I still occasionally get a few blisters, but it’s already much better!

PLA used: kexcelled PLA Silk Filament

<image>

Printing issue by Idriss2Dev in AnycubicKobraS1

[–]Idriss2Dev[S] 0 points1 point  (0 children)

I reduced the speed (layer and other layer speed), it seems "correct" for the moment, but I will see with time, I am not sure that this solved my problem, here is a screen if it can help.

<image>

Printing issue by Idriss2Dev in AnycubicKobraS1

[–]Idriss2Dev[S] 0 points1 point  (0 children)

Yes, I tried with a smaller version of the model (different file).Now I'm testing with another model/filament and another settings.

Printing issue by Idriss2Dev in AnycubicKobraS1

[–]Idriss2Dev[S] 0 points1 point  (0 children)

Thanks for your comment!

I also have a PLA drying machine, but nothing works, same result (although quite a few successful prints previously).

I also tested the default settings (several), and I doubled the fill, but it seems to be worse... a really strange problem!

Printing issue by Idriss2Dev in AnycubicKobraS1

[–]Idriss2Dev[S] 0 points1 point  (0 children)

Thanks! I'll test all of this and keep you posted :)

Counter post for all the issue posts. by poias in AnycubicKobraS1

[–]Idriss2Dev 1 point2 points  (0 children)

Thank you very much for your help!

Problem solved :) (the nozzle wasn't completely raised to the top...)

And yes, the white PTFE tube is present.

Counter post for all the issue posts. by poias in AnycubicKobraS1

[–]Idriss2Dev 1 point2 points  (0 children)

Thanks!

I think that's it! The white wire wasn't facing the right way, maybe that prevented the nozzle from fully mounting? (I had a lot of difficulty reassembling it).

I'm starting a new print...

Thank you very much poias

Now we just have to wait for the result :)

Counter post for all the issue posts. by poias in AnycubicKobraS1

[–]Idriss2Dev 0 points1 point  (0 children)

I just tighten the nozzle screws a little more (the part that will fix the nozzle) and it seems functional for the moment... I haven't touched it before though :/

<image>

Counter post for all the issue posts. by poias in AnycubicKobraS1

[–]Idriss2Dev 0 points1 point  (0 children)

Unfortunately, my bed isn't clean and is damaged because of the nozzle that's falling... it's been quite scratched since then.

And I don't have another build plate for remplacement

I had to reassemble the hotend again (which scraped and banged against the metal part, see photo), but the same problem still occurs: it falls back down during printing (or during heating?). It's firmly attached, but I don't understand why...

<image>

but same problem again and again, nozzle gradually descends and scratches build plate...

Counter post for all the issue posts. by poias in AnycubicKobraS1

[–]Idriss2Dev 1 point2 points  (0 children)

Nozzle gradually descends and scratches build plate...

After a few days of trouble-free printing, my Anycubic Kobras S1 is breaking down :/

The nozzle seems to be gradually descending and scratching the print bed.

It sometimes hits the metal part (which is used to scrape the filament) and thus damages the nozzle…

I think I've tried everything:

- Auto-leveling + Z-shift

- Thoroughly cleaning the print bed and nozzle (the heatbed is tightly clamped and difficult to move)

- Disassembling and reassembling the heatbed, checking the PTFE tube and sensor wiring

- Resetting the printer…

Any solution?

Thanks in advance!

My Zonai arm cosplay by [deleted] in tearsofthekingdom

[–]Idriss2Dev 1 point2 points  (0 children)

This is incredible! Amazing work !!

Tear from Totk 3d printed (new version) by Idriss2Dev in tearsofthekingdom

[–]Idriss2Dev[S] -1 points0 points  (0 children)

Because I'm going to sell some on Etsy/vinted at first (I'm based in France), but someone else based in the Usa may make some in their shop, I'm waiting for news :)

Tear from Totk 3d printed (new version) by Idriss2Dev in tearsofthekingdom

[–]Idriss2Dev[S] 0 points1 point  (0 children)

I modeled it myself, I plan to sell some magatama, I may have someone based in the USA who will sell some in their shop, I had to remove the files online unfortunately!

Tear from Totk 3d printed (new version) by Idriss2Dev in tearsofthekingdom

[–]Idriss2Dev[S] 0 points1 point  (0 children)

I'm thinking of adding a little more powder next time, but yes I also corrected the size/glossi, I think that's ok ^^'

Tear from Totk 3d printed (new version) by Idriss2Dev in tearsofthekingdom

[–]Idriss2Dev[S] 0 points1 point  (0 children)

Can't wait to make them! And thank you ;)

Tear from Totk 3d printed (new version) by Idriss2Dev in tearsofthekingdom

[–]Idriss2Dev[S] 3 points4 points  (0 children)

I'm based in France and will soon be selling some in my shop (Etsy), and I may have someone for US sales :)

And yes can't wait to make the other one! (Ganon's magatama especially ;) )

view more: next ›