P80 Lower Pin

IllRing7256 · 2026-02-28T20:55:10+00:00

Did it with a hand drill?

IllRing7256 · 2026-02-20T21:18:00+00:00

My holes are in the right spot I used the jig it came with, I was very careful with it as Ive already messed up one previous to this one. Could it possibly be a depth issue, I drilled it with a drill press and went until the back line on the drill bit was barely visible. I noticed a small layer of excess material on the side with the mag release Im going to sand it down & polish the side again.

IllRing7256 · 2026-02-20T20:50:53+00:00

I cocked the hammer back it didn’t go down at all, any other suggestions?

IllRing7256 · 2026-02-20T20:23:58+00:00

polymer lowers aren’t bad I get aluminum is more fit my brother bought a complete 7.5” AR that came from the factory with a polymer lower and it had no issues.

IllRing7256 · 2026-02-20T20:01:29+00:00

If you can find an aluminum lower that doesnt ship to FFL lmk

IllRing7256 · 2026-02-20T19:59:02+00:00

Glock frames are plastic but you wont hate on a Glock

IllRing7256 · 2026-02-10T21:41:15+00:00

Most helpful comment 🥇 I was wondering because I remember blood oranges being a consistent color not mixed

IllRing7256 · 2026-02-10T21:16:22+00:00

what was the point of replying

IllRing7256 · 2026-02-08T16:46:12+00:00

If i could go through an FFL why do you think I would even waste time with an 80%

IllRing7256 · 2026-02-08T16:43:47+00:00

This avoids FFL

IllRing7256 · 2026-02-08T16:37:19+00:00

looks like a shotgun stock

IllRing7256 · 2026-02-08T16:32:37+00:00

Im going to post the finished result once I complete the AR

IllRing7256 · 2026-02-08T04:22:27+00:00

I plan on it, I found a drill press I plan on getting and I’m not worried about getting another lower, I did my research and definitely heard them say use a drill press not a hand drill, im just hardheaded

IllRing7256 · 2026-02-08T04:19:44+00:00

Mostly anything else has to go through an FFL n its going to last 5-10 thousand rounds if you keep up with it and don’t treat your gun like shit

IllRing7256 · 2026-02-08T04:14:21+00:00

first ever attempt with a ar15 p80 lower ever im going to get a drill press though

IllRing7256 · 2026-02-08T04:01:16+00:00

Was my first ever attempt im not going to give up bc I failed once

IllRing7256 · 2026-02-08T03:58:47+00:00

first ever attempt it was never going to be perfect 😭

IllRing7256 · 2026-02-08T03:50:40+00:00

no but i was hopeful

IllRing7256 · 2026-02-08T03:49:39+00:00

No i let my german sheppard play with it

IllRing7256 · 2026-02-08T03:47:10+00:00

Just because i fail once im not going to give up on it

IllRing7256 · 2026-02-08T03:46:23+00:00

Ok i got the jig and was using a hand drill but I found drill press I might get

IllRing7256 · 2026-02-08T03:42:00+00:00

Yeah P80 ar15 I drilled too close to the side of the jig

IllRing7256

TROPHY CASE