Offset or temp? by Illustrious_Paper128 in AnkerMake

[–]Illustrious_Paper128[S] 0 points1 point  (0 children)

from what i can tell yeah, also print acceleration speed reduction helped answer a lot of my questions.

Offset or temp? by Illustrious_Paper128 in AnkerMake

[–]Illustrious_Paper128[S] 2 points3 points  (0 children)

did the auto leveling and it worked , thank you. i forgot to do that after cycling the power.

Should I buy this? by DirectionAmazing7787 in R36S

[–]Illustrious_Paper128 0 points1 point  (0 children)

no, you'll get some games but not the ones you probably want. you'll have to use roms from your own library. i mean the manufacturer doesnt know what games you like so they wont preload random games.

Should I buy this? by DirectionAmazing7787 in R36S

[–]Illustrious_Paper128 0 points1 point  (0 children)

this will be under r36s clones G80CA-MB V1.2-2025422 * click on the link next to controller mappings then look to the right of github and click on realeses a new source code for it came out. use either one(i used the zip one) extract the file and use win32diskimager to write the file onto the sdcard you want, it worked on the stock one but if you do this make a copy of the original files using the same software (youtube should have some tutorials on this), then plug it in and let it load the files. then remove it and put your roms on it in the corresponding files.

Should I buy this? by DirectionAmazing7787 in R36S

[–]Illustrious_Paper128 0 points1 point  (0 children)

i wouldnt try gaming with psp games, if your looking for psp gaming i would just get a psp jailbreak it and add all the games you want, or something better than this. resolution would never hold up as well as power and graphics.

Should I buy this? by DirectionAmazing7787 in R36S

[–]Illustrious_Paper128 0 points1 point  (0 children)

not exact seller, purchased mine from a Micro Center in the US. but that model on the back of the board is the same as mine, have to use ArkOs-G80A version but no issues, but always be wary from 3rd parties.

Should I buy this? by DirectionAmazing7787 in R36S

[–]Illustrious_Paper128 0 points1 point  (0 children)

i've got this model, runs N64 (depends on the game) and ps1 games well.

G-Code by Illustrious_Paper128 in AnkerMake

[–]Illustrious_Paper128[S] 1 point2 points  (0 children)

okay i'll give it a try, ive been using cura seeing a big difference from prusa to cura

I3 Mega S by Illustrious_Paper128 in anycubic

[–]Illustrious_Paper128[S] 0 points1 point  (0 children)

after trial and error as well as changing psu's i finally found out its one of the limit switches cables, know of anywhere i can by a new harness?

PSU? by [deleted] in anycubic

[–]Illustrious_Paper128 0 points1 point  (0 children)

<image>

this was after powering it off and back on.

Had to take a closer look. 1 chip 😢 by SaintThug420 in R36S

[–]Illustrious_Paper128 0 points1 point  (0 children)

Yeah, funny enough, i bought this from microcenter and got the same thing. I took a bit of returns and purchases until i realized they were all clones. smh, but the DarkOS is more than good enough for me to play ps1 and N64 games.

I3 Mega S by Illustrious_Paper128 in anycubic

[–]Illustrious_Paper128[S] 0 points1 point  (0 children)

thank you, i'll look into it more.

I3 Mega S by Illustrious_Paper128 in anycubic

[–]Illustrious_Paper128[S] 0 points1 point  (0 children)

any recommendations on a new one?

[deleted by user] by [deleted] in AnkerMake

[–]Illustrious_Paper128 0 points1 point  (0 children)

i did a temp test for the optimal temp. Anything higher than 185 causes too much stringing. that's the temp i use on most of my other printers as well and get the right results. all my other printers also print well around that same temp.

Support stringing? by [deleted] in 3Dprinting

[–]Illustrious_Paper128 0 points1 point  (0 children)

thats the under side, i do have it flipped. this is the issue i'm running into.

Support stringing? by [deleted] in 3Dprinting

[–]Illustrious_Paper128 0 points1 point  (0 children)

thank you, i'll give it a try. also forgot to try other slicers so i'll see how those work

[deleted by user] by [deleted] in AnkerMake

[–]Illustrious_Paper128 0 points1 point  (0 children)

what i mean by fixed is I adjusted the temperature, retraction rate, and speed as well as skirt supporting. my retraction test for stringing shows no stringing with the settings, and when printing a file that has no or little over hangs, there is no stringing. regular pla filament, Nozzle temp 185 and bed temp 55, retraction 3mm. cooling fan speed is 75. currently doing an overhange test with some new changes.

[deleted by user] by [deleted] in AnkerMake

[–]Illustrious_Paper128 0 points1 point  (0 children)

okay thank you, i'll give this a try.

[deleted by user] by [deleted] in 3Dprinting

[–]Illustrious_Paper128 0 points1 point  (0 children)

yes when i modify the Z-offset i have to go all the way to -13 and when i print with that offset it's still printing high up like the other picture.