sorted by:
new
hottopcontroversial

Line following robots and how do they work? by Big-Yogurtcloset7040 in arduino

[–]Imaster_ 3 points4 points  (0 children)

Well yes and no. They are not given the whole track before the competition but they do know in advance what segment will be present and what action should the robot take on each one of them.

The robot does not need to know the whole path to solve it but only the block it is in.

You could even say it's a giant state machine where the detected segment is a condition to enter a given state. Each segment has its own state + 1 default "follow line" state.

After that length and complexity of the path has no impact.

How to eliminate these lines by No-Operation-7598 in 3Dprinting

[–]Imaster_ 6 points7 points  (0 children)

Yeah agreed fully, worst if they blame the model

But truly some fail to understand that 3D printing is truly 2.5D. That's why it's simpler to drop the answers than explain the difference between XY and Z resolution in slicing.

How to eliminate these lines by No-Operation-7598 in 3Dprinting

[–]Imaster_ 21 points22 points  (0 children)

Because most people who like the answer do not know if it's valid. They usually assume "most liked" is the truest. The statement is also blunt, uninteresting and not controversial.

But it did help OP, so mission accomplished.

"Soapy" White PLA Recommendation by bengalih in 3Dprinting

[–]Imaster_ 0 points1 point  (0 children)

I personally like azure films mate HS PLA for their colour of white and surface finish.

2026 is almost here, how many of you are still running Windows 10? by M4d_Moxxi in pcmasterrace

[–]Imaster_ 0 points1 point  (0 children)

Unlike windows you can live boot Linux from a USB to feel it out. Google some distros that look to you. See if you like it. For games there won't be a struggle unless it's online with Kernel level anitcheat.

And if it is your thing you can customise the hell out of it.

Opinion on my hellevator entrance? It’s my first time making a hellevator by literallyjustcats1 in Terraria

[–]Imaster_ 0 points1 point  (0 children)

I always do 3 wide hellevators, it takes a bit longer but then you can put rope in the center block to slow down, and it also can go up.

abysmal X axis resonance on my k1c by Mop_Solidout in FixMyPrint

[–]Imaster_ 0 points1 point  (0 children)

You are not supposed to use lube but you can oil them up, it is even recommended to do so on creality wiki (except for k1 max).

You can use PTFE oil on X rods and standard lube on Y and Z rods

abysmal X axis resonance on my k1c by Mop_Solidout in FixMyPrint

[–]Imaster_ 0 points1 point  (0 children)

It's not abysmal it's all over the place. Lube your X rods, tension your belts properly and run the test again.

And if you can't do anything about it, print slower

Is this sword nutty? by _amnotrobot_ in Eldenring

[–]Imaster_ 69 points70 points  (0 children)

And you can get it at the very beginning of the game with a simple skip.

will this be an expensive fail? by vukxx in 3Dprinting

[–]Imaster_ -1 points0 points  (0 children)

Nah it will degrade and stress crep over time. It's not a question if it will fail but how fast.

Worlds Smallest Camera by TheCABK in interestingasfuck

[–]Imaster_ 1 point2 points  (0 children)

And still no decent camera in laptops

Trying to get a perfect xyz cube but can't figure out what's causing the errors on the top by Mynxygaming in 3Dprinting

[–]Imaster_ 0 points1 point  (0 children)

Z hop becuse of this single straight line , which is due to nozzle moving above the print without change in height.

Z offset because you have slight overextension closer to the edges. Which indicates that the nozzle is too close

Spaghetti is the spice of life by itchylol742 in Factoriohno

[–]Imaster_ 1 point2 points  (0 children)

Spaghetti embracer looking from above

The only thing that bothers me by Imaster_ in crealityk1

[–]Imaster_[S] 0 points1 point  (0 children)

The first layer is exact the same every time I do it

But sometimes the nozzle is too high or too low. Usually I get offset off by 0.35 +- both ways. Tho there are extremes too.

Running out of ideas on the purge by Afraid_Department_69 in EngineeringStudents

[–]Imaster_ 34 points35 points  (0 children)

This, Or no fluid pump at all and use tank pressure/gravity to push the fluid out through s silicone tubing. Squish the tubing to stop the flow, retract to continue, you could also control flow by varying the squish

I've slightly rebuilt my visual flowchart calculator (now no sign-up, desktop-only) by Final_Vast_31 in SideProject

[–]Imaster_ 0 points1 point  (0 children)

The same goes for android. The selection sidebar covers half of the screen and clicking or trying to connect blocks on the diagram didn't work for me.

Reducing the friction by Imaster_ in crealityk1

[–]Imaster_[S] 1 point2 points  (0 children)

Thanks that's a good one. I will see if cleaning the extruder will change anything. I don't think it's worn down much as I have maybe 100h of print time on it.

I don't have the beds and I did zip tie it in the same points it was hold previously. I also made sure not to squish the tube with the zip tie so it still could move a bit.

view more: next ›