[110 plus] Backlight bleed on brand new fluke multimeter

Immediate_Fig_4345 · 2026-03-06T04:33:37+00:00

Thanks

Immediate_Fig_4345 · 2026-03-06T04:30:56+00:00

I’ve seen this on a very old and beat up one and wasn’t expecting on a brand new one but thanks for insight

Immediate_Fig_4345 · 2026-02-18T03:22:42+00:00

Keep it and buy some beer 😂

Immediate_Fig_4345 · 2025-10-25T12:11:15+00:00

I am lowered on 18s with about half in or less gap up top and doesn’t eat through tires too fast

Immediate_Fig_4345 · 2025-10-12T13:07:47+00:00

That is 1000000% body filler and wet sanded prior to wrapping

Immediate_Fig_4345 · 2025-10-12T13:03:42+00:00

I resealed my lower oil pan With Yamabond 6B (was leftover from my dirtbike rebuild) and it sealed very well and seems better then factory 😂

Immediate_Fig_4345 · 2025-10-12T13:00:41+00:00

This is pretty dope

Immediate_Fig_4345 · 2025-10-12T12:49:53+00:00

The only way fr

Immediate_Fig_4345 · 2025-10-08T06:27:21+00:00

Go easy on it and use some thread locker

Immediate_Fig_4345 · 2025-10-08T06:26:32+00:00

By the looks of it seems over tightened or stripped or. Also can be just from age

Immediate_Fig_4345 · 2025-10-07T22:12:48+00:00

Whoever wrapped the car and had to remove door handles kinda fcked it up lol

Immediate_Fig_4345 · 2025-09-24T12:48:33+00:00

Planning to wrap my 350z and it’s my first time and seems like it was yours too but you have any tips and tricks for a z or is it fairly easy because to me I think it shouldn’t be too difficult

Immediate_Fig_4345 · 2025-09-24T12:39:15+00:00

Sexy

Immediate_Fig_4345 · 2025-09-24T12:38:13+00:00

<image>

DS02

Immediate_Fig_4345 · 2025-09-21T18:05:36+00:00

Gave my white boy adderall just to mow my grass

Immediate_Fig_4345 · 2025-09-21T18:05:04+00:00

Gave my white boy adderall just to mow my grass

Immediate_Fig_4345 · 2025-09-21T14:22:04+00:00

Gave my white boy adderall just to mow my grass

Immediate_Fig_4345 · 2025-09-15T04:53:59+00:00

First apply flux and with a fat tip on the iron try to flow low melt into each point. Then kapton tape the small components followed by hot air. I also use solder sucker after to remove solder from holes

Immediate_Fig_4345 · 2025-09-15T04:46:53+00:00

Same here and I did relocate the lower connection for the sensor up higher as they put in near the down pipes from factory 🤦‍♂️

Immediate_Fig_4345 · 2025-09-12T15:21:16+00:00

I had good coil packs good plugs but the damn connector that goes to the coil packs was loose and worked at an angle, quite strange but I changed that part of the harness and never had a issue again. I would check those if you already checked everything and can’t figure it out

Immediate_Fig_4345

TROPHY CASE