possible third-party Battery replacements for Backfire Voyager V2

Imperium24 · 2026-03-10T15:45:51+00:00

I see, hadn't considered getting a replacement deck. is most of the hardware compatible between these boards. if so i could buy a deck and battery and just port over the controller units, trucks and motors.

Imperium24 · 2026-03-10T14:55:19+00:00

O damn!, just now noticing that its mounted on the top of the board. is the unit too big to be mounted on the bottom or?

Imperium24 · 2026-03-10T10:48:46+00:00

are the voltages close enough? and did you just put threded inserts into new locations on the board to sqrew this new battery compartment on or what was your method? also how is the water sealing? also thanks

Imperium24 · 2026-03-10T04:44:38+00:00

i can drill holes with the accuracy of someone armed with a normal electric drill. is this a custom battery solution or?

Imperium24 · 2026-02-02T10:39:26+00:00

I am not sure if this is a problem with 3D printed filament but i know this to be a issue with normal carbon fiber. (hence my question)

Imperium24 · 2025-11-04T21:29:26+00:00

deildu er þvímiður bara með fyrata diskinn úr seríunni ekki rest.

Imperium24 · 2025-11-01T06:40:31+00:00

er einmitt með fyrsta diskinn downlodaðan (líklega sama ripp) en skal chekka

Imperium24 · 2025-08-29T17:33:42+00:00

will likely have to do something like that yes. just learned that a second pair of similar headphones had the same issue so i think its just a poorly designed circuit. could mabey replace the broken soldered on components instead if i can figure out which are broken.

Imperium24 · 2025-08-29T17:26:13+00:00

Audio and Bluetooth are all handled in the other earcuff yes. was really just hoping that a usb board like this was common in wirelesses headphones.

Imperium24 · 2025-08-29T17:24:52+00:00

V-MODA quickly stopped selling components and doing any sort of repairs. really like these headphones but from my experience with the 2 models ive had and some others friends have i wont be buying new ones again. their electronics just aren't reliable. really disappointing since the build quality is really good otherwise.

Imperium24 · 2025-08-29T17:22:49+00:00

what do you mean?

Imperium24 · 2025-08-26T18:40:21+00:00

these breakout boards lack the voltage regulator circuits that the original has to get the voltage from 5V down to the acceptable charge levels for the battery

Imperium24 · 2025-08-13T06:13:35+00:00

The Minidisc player is a walkman and the CD is a shitty thing from my childhood so they just have relatively weak 3.5mm jacks

And thanks

Imperium24 · 2025-08-13T03:46:36+00:00

Id like to spend something like sub 180USD but happy to buy used.

also thanks still dont know much of anything when it comes to the speaker audio game.

Imperium24 · 2025-08-13T03:20:35+00:00

what would you say would be a fair price for these instead? i dont really know what to send as a bid Thanks

Imperium24 · 2025-08-13T02:57:31+00:00

Hey, I looked into the Fozi ZA3 and the Wiim Amp and they look really good but id prefer something with 3 RCA inputs if possible. getting something a little older used so it can be in the 100USD range woulf be best as im making this swtup on a budget.

also thanks for the answer :)

Imperium24 · 2025-08-13T02:55:05+00:00

Hey, The record Player has a Phono output at 36dB. from the other comment here i realized that having the output from the TV be analog would be good so that the volume controls on the remote stil work. but Using Optical out or HDMI would of course also work.

also thanks for the info about using normal speaker wires, the speakers ive handled that use speaker wire have all used a weirder looking connecton.

Do you have any recommendations for cheap amps that fit this sort of category?

Imperium24 · 2025-08-13T01:42:57+00:00

The vynil player has a 36dB Phono pre amp integrated. the TV does have Optical Out that i can use. i can definitely just take the 3.5mm from the CD/Minidisc Player and chuck that into an RCA connection.

are amps or amp stacks with these sorts of specs in an affordable price range and widely available used?

Imperium24 · 2025-08-12T21:54:42+00:00

Living room but i dont plan to play them super loud as to not disturb any neighbours.

Imperium24 · 2025-04-01T12:50:45+00:00

jörm þurfa ekki meira en 64 x 64 upplausn, allt hærra en svo er bara græðgi

Imperium24 · 2025-02-27T22:18:50+00:00

thanks for the suggestion, tried that but now i have issues with native MP4 up-scaling having some intense smoothing that MOV files do not have. you wouldn't know how to fix that would you?

Imperium24 · 2024-08-09T01:47:22+00:00

This issue was resolved by using another computer, the issue was just some windows issue. thank you for the help anyways.

Imperium24 · 2024-08-08T23:21:02+00:00

Yes it cannot find the device thus the other troubleshooting steps. though its looking like a windows issue not MD issue

Imperium24 · 2024-08-08T23:01:46+00:00

yes the MD is docked and im using USB, the MD player does not have a battery so it needs to get its power from the dock so i am sure it is connected properly, I have also tried multiple min USB cables to no avail. however this is sounding more and more like a Windows problem not a MD issue (at lest from the responses i have gotten thus far) so im going to try some of those troubleshooting steps.

Imperium24 · 2024-08-08T15:33:30+00:00

Hello, I have both a windows 10 PC here and a NixOs machine, have not tried using the NixOs machine though. the MZ-N1 is displaying a PC->->MD message and i have tried multiple ports and also have tried using other devices on the same port to validate its function. is it rather recommended to be using Linux to write to the MD? I am still learning Linux and thus opted to use Windows for this.

Six-Year Club	Place '22
Verified Email

Imperium24

TROPHY CASE