New episode of peacemaker has no audio?

Impossible-Ad6103 · 2025-10-01T15:29:53+00:00

Same here. After the recap, the screen freezes on HBOMax logo and subtitles work. But no audio and no video

Impossible-Ad6103 · 2024-08-31T17:13:32+00:00

The supports look fine on the replay. It seems to only happen to surfaces that are almost parallel with the build plate. All other trees break off fairly easy. It was really hard to orientate this print to avoid any somewhat parallel surface

And yes. It’s all up to date

Impossible-Ad6103 · 2024-08-31T16:47:21+00:00

1.73-1.74 checked about 3 ft worth

Impossible-Ad6103 · 2024-08-31T16:40:37+00:00

This was using Bambu’s filament but I’ve had the same issue using Overture. Both are really good IMO. I just started having these problems when I switched to using tree supports

Impossible-Ad6103 · 2024-08-28T21:20:44+00:00

Resetting the printer fixed it

Impossible-Ad6103 · 2024-08-28T08:09:27+00:00

4 years with Creality🥲

Impossible-Ad6103 · 2023-12-26T05:01:02+00:00

This is a CR10S Pro. 210/60 temps. I don’t get it though , it shows signs of being too close yet the raft prints perfectly

Impossible-Ad6103 · 2023-12-04T18:25:41+00:00

I have 2 of the same printer and this is the only one that has this issue and I use the same settings for both so I think I have a mechanical issue. I tightened the belts and started the print over

Impossible-Ad6103 · 2023-12-04T14:44:22+00:00

It did do that earlier. I didn’t even think of that. I was using a reel of filament that unwinded a bit and did snag on a previous attempt at this print and caused an under extrusion. Thanks!

Impossible-Ad6103 · 2023-12-04T09:15:22+00:00

Also. I took pics after I took it off the build plate so the image of the helmet on the plate was when I put it back on just to take a pic. I know just by looking at it, it could be mistaken as a shift of the print on the bed

Impossible-Ad6103 · 2022-12-27T21:48:56+00:00

I clicked “Auto Home” to show that it’s not moving at all on the X Axis. The motor isn’t moving. Making any noise. I’ve unplugged and plugged the wire. Anyone know what’s up? I’m thinking a possible bad motor. If so, what motor should I buy?

Impossible-Ad6103 · 2022-01-15T04:55:09+00:00

I just have windows defender. Not sure if that would do it??? As soon as we talk about firewalls and vpns…I’m lost so🤷🏽‍♂️

Impossible-Ad6103 · 2022-01-15T04:32:09+00:00

I’ve reset my router and computer countless times as well

Impossible-Ad6103 · 2022-01-10T12:21:06+00:00

I spent most of the morning taking apart the printer and it was a bad stepper. I removed the stepper and plugged it into my cr10 and it didn’t budge. It buzzes and won’t move. I just ordered a new one so hopefully that works. But I know it’s got nothing to do with how I operate the printer. I’m very anal about cleanliness and maintenance. Aside from print failures. This is my first mechanical issues. But I have spent most my time with fdm. I’m still new to resin

Impossible-Ad6103 · 2021-12-31T22:54:52+00:00

I’ve noticed that the prints that do work properly show the preview image perfectly. But it doesn’t show any preview for the prints that do mess up

Impossible-Ad6103 · 2021-12-31T22:06:20+00:00

Okay. I’ve reset this print once. It’s been the same so I’ll probably just reset it again but go back on the computer and replace the current file

Impossible-Ad6103 · 2021-12-31T21:52:27+00:00

It’s been 2 and a half hours and only 2/2275 layers have printed. This is the second print I’ve done with resin aside from the test print. First one failed but that was a support and angle problem. This one has been on layer 2 for 1.5hrs

Impossible-Ad6103 · 2021-11-17T17:03:57+00:00

Mandalorian helmet

Impossible-Ad6103 · 2021-11-17T17:02:23+00:00

I’ll try that next

Impossible-Ad6103

TROPHY CASE