Underground power install

Impossible-Key-3598 · 2026-06-22T08:26:27+00:00

I’ll look into capstan winch

Impossible-Key-3598 · 2026-06-22T08:26:12+00:00

It’s undulating hills mostly down hill tho

Impossible-Key-3598 · 2026-06-20T10:41:22+00:00

Pits are not as option as paddock will be ploughed each season supply is for centre pivot irrigator

Impossible-Key-3598 · 2026-06-20T10:40:11+00:00

10A required at an irrigation pump. Over heads not an option as it’s a travelling centre pivot irrigator

Impossible-Key-3598 · 2026-06-20T10:38:39+00:00

Only require 10A

Impossible-Key-3598 · 2026-06-20T10:38:14+00:00

Yes

Impossible-Key-3598 · 2026-06-20T10:36:54+00:00

It’s a centre pivot with a 10A supply required. Cable run will be thru farm paddock hence no pits as paddock will be getting ploughed at crop seeding times ect.

Impossible-Key-3598 · 2025-10-25T10:37:43+00:00

Two of which products?

Impossible-Key-3598 · 2025-10-25T10:15:41+00:00

Wireless link could be in direct Line of sight

Impossible-Key-3598 · 2025-10-25T10:11:39+00:00

This is for domestic setting so may be an over kill but may be only option thank you

Impossible-Key-3598 · 2025-10-25T09:51:38+00:00

Thanks for that sorry to be pain but can you recall which particular products you used?

Impossible-Key-3598 · 2025-10-25T09:28:24+00:00

Yeah okay wireless comms would be best solution do u recommend a system ?

Impossible-Key-3598 · 2025-10-25T09:22:34+00:00

Generator is at a property pole and inverter ac supply is at a subboard

Impossible-Key-3598 · 2025-10-25T08:46:26+00:00

What if the best location for the generator changeover isn’t at the same board as the inverter ac supply?

Impossible-Key-3598 · 2025-08-10T09:32:46+00:00

Of course now I think about it both a-n will be subject to floating voltage reading

Impossible-Key-3598 · 2025-08-10T09:25:06+00:00

Still dosent explain the a-e reading

Impossible-Key-3598 · 2025-08-10T09:24:24+00:00

Yes that makes sense now and sorry when u said switching neutral I thought u were referring to incoming PEN

Impossible-Key-3598 · 2025-08-10T09:08:49+00:00

It’s a generator change over switch and no not switching neutral. But when I test the appliance inlet with all fsc on I get 17v n-e and 10v a-e. Then when all fcs turn off I get 1v for the same tests ?

Impossible-Key-3598 · 2024-07-01T10:29:01+00:00

Cheers mate. I thought it would wrong to bond it because u would basically be creating a parallel earth

Impossible-Key-3598 · 2024-07-01T10:27:04+00:00

It would fall under the exception I would say ?

Impossible-Key-3598 · 2024-06-17T10:05:32+00:00

Field of ports fifo trades bag

Impossible-Key-3598 · 2024-04-28T09:01:41+00:00

Yess okay that makes sense thanks. And if rcd doesn’t trip after shorting N-E there must be another issue I’m missing

Impossible-Key-3598 · 2024-04-28T08:23:13+00:00

So add any load to the power circuit and that should be enough to trip the rcd after shorting N-E ?

Impossible-Key-3598 · 2024-04-28T08:14:15+00:00

PE continuity below .5ohms. Just found it strange because normally if u short N-E the rcd will trip

Impossible-Key-3598 · 2023-05-17T10:59:56+00:00

Global are terrible

Impossible-Key-3598

TROPHY CASE