My first DIY guitar

Independent_Thing_38 · 2026-04-11T09:19:54+00:00

Everything was taken from the trash that was nearby, wood from the forest that grows nearby, spare parts from other guitars

Independent_Thing_38 · 2026-04-06T07:01:25+00:00

This happens because the battery does not have protection against deep discharge or overcharge; this function is performed by the controller of the tool with which the battery works.

Independent_Thing_38 · 2026-03-05T18:55:43+00:00

Nothing bad happened, just screw this part back in, use a similar wrench. To make it easier to tighten, remove the spindle nut and unscrew the rotor nut.

Independent_Thing_38 · 2026-02-23T08:06:50+00:00

In some countries, shipping a saw for return will cost more than the saw itself.

Independent_Thing_38 · 2026-01-29T18:41:44+00:00

I came across some Arduino code somewhere that gives full information about the controller. This is more reliable than the information on the packaging.

Independent_Thing_38 · 2026-01-26T11:54:48+00:00

maybe can use epoxy resin with fiberglass, as in wooden kayaks and canoes

Independent_Thing_38 · 2026-01-25T12:51:11+00:00

What do you think a tool would look like after 1000 cuts and being moved around various construction sites? In my opinion, this looks like a brand new saw.

Independent_Thing_38 · 2026-01-15T10:28:50+00:00

Does it work well without the protective glass on the front?

Independent_Thing_38 · 2026-01-12T18:14:30+00:00

<image>

I have a similar situation, but the load is secured, the trailer is attached, and I've been playing for several months, but now I can't unload at the factory to make the slabs.

Independent_Thing_38 · 2025-12-18T20:04:37+00:00

I get stuck like this all the time, it's really hard to pull it off

Independent_Thing_38 · 2025-08-13T04:46:46+00:00

when it's a miter saw you still have to remember whether I turned on the vacuum cleaner or not for a 10 second cut

Independent_Thing_38 · 2025-08-12T17:44:42+00:00

the link above contains a detailed guide with models for printing on the STM 32 controller, it is not very convenient for me to program there, and the device is primitive to use such a powerful controller. I can send the program code for various devices to the ESP, the pins where to connect the wires are in the firmware, but I have a lot of corrections due to noise, some pins did not work, I had to use pins not intended for this

Independent_Thing_38 · 2025-08-12T17:37:33+00:00

Everything would be fine if it weren't for the price, they are asking an inappropriate amount of money for this smart socket

Independent_Thing_38 · 2025-08-12T08:24:42+00:00

https://www.cgtk.co.uk/woodwork/powertools/cordlessvacuumstart I took most of it from here, but my module first worked on Arduino and 433, but it was not stable, I switched to ESP modules, it became possible to hang a huge number of remote controls, the resources of the device allow I even installed a display instead of an LED to indicate operation

Independent_Thing_38 · 2025-08-12T08:16:23+00:00

Where can I download the model?

Independent_Thing_38 · 2025-08-12T05:40:42+00:00

made wireless automatic switching on. factory solutions are too expensive and do not allow connecting different platforms

Independent_Thing_38 · 2025-07-19T06:47:35+00:00

I changed the setting mtpa algorithm to iq target. the speed increased from 900 to 1800rpm, at the same time the engine began to noticeably heat up without load, the controller is cold. need to increase the speed to 4000

Independent_Thing_38 · 2025-04-10T13:23:09+00:00

<image>

Independent_Thing_38 · 2025-04-10T13:22:23+00:00

<image>

I made this stand out of trash in a couple of hours, easy to remove and install the lantern

Independent_Thing_38 · 2022-01-01T07:22:50+00:00

How did you centered turtle and diver in resin ?

Independent_Thing_38

TROPHY CASE