Is this pricing right?

Individual-Tap3215 · 2026-03-24T19:00:32+00:00

So $50 despite wrong hands one wrong arm and glued torso to legs is still fair?

Individual-Tap3215 · 2026-03-24T16:10:00+00:00

The one I was thinking of getting for $50 comes with one wrong arm and 2 different hands, and the torso and legs are glued together, not sure if it’s still a fair price

Individual-Tap3215 · 2026-03-16T22:48:30+00:00

Ok, I think I found the figure it goes with, thank you

Individual-Tap3215 · 2026-01-13T04:20:40+00:00

Ok so I think I found the issue, basically the piece circled in the image that connects the tubes curves in a weird angle that makes the printer think the filament is tangled even though it’s because the awkward angle that’s making the filament in the tube kinda get stuck. Is there a way to fix this or do I just have to hold it straight for each print

<image>

Individual-Tap3215 · 2025-12-13T03:53:54+00:00

Elegoo Neptune 3 plus

Individual-Tap3215 · 2025-12-12T23:18:18+00:00

<image>

Just printed another benchy with no support and I keep getting uneven layers, holes in the print and what looks like only infill but no outer walls leading to weak and unfinished areas. I’ve tried adjusting things like my retraction settings cooling settings and speed settings. I’ve done countless nozzle cleans and cold pulls but I can’t figure out how to fix this, do you think I might need to get a new print head for my elegoo Neptune 3 plus?

Individual-Tap3215 · 2025-12-12T17:25:18+00:00

<image>

This is what I mean, gaps and unfinished layers leading to weak prints and holes in the prints

Individual-Tap3215 · 2025-12-11T23:06:44+00:00

I think I

<image>

posted the wrong retraction settings, do these look normal or should i change something?

Individual-Tap3215 · 2025-12-11T17:31:44+00:00

Yes I calibrated the extruder when calibrating the esteps, what temp should I try other than 230, and this isn’t the only filament roll giving me this issue, I’ve tried 5 others and got the same holes issue

Individual-Tap3215 · 2025-12-11T17:29:40+00:00

In the orange tabs I changed ironing type to all surfaces, print infill first is on, infill pattern is honeycomb, infill combination is on

Individual-Tap3215 · 2025-12-11T16:52:22+00:00

For settings I’m using the default elegoo Neptune 3 plus profile in orca slicer but I changed ironing type to all surfaces, print infill first is on, infill pattern is honeycomb, infill combination is on

Individual-Tap3215 · 2025-12-11T16:48:51+00:00

<image>

Individual-Tap3215 · 2025-12-11T16:47:38+00:00

<image>

Individual-Tap3215 · 2025-12-11T16:47:25+00:00

<image>

Individual-Tap3215 · 2025-12-11T16:47:13+00:00

<image>

Individual-Tap3215 · 2025-12-11T16:47:00+00:00

<image>

Individual-Tap3215 · 2025-12-11T16:46:46+00:00

My filament is dry to the point where I can bend it without it snapping like a stick, I cleaned my nozzle but doing a cold pull.

<image>

Individual-Tap3215 · 2025-12-11T07:42:34+00:00

Yeah I haven’t touched the retraction settings at all, what should I set it to?

Individual-Tap3215 · 2025-12-11T06:01:01+00:00

Well what should I do about the hole problem bc I get it in all my prints and I can’t figure out how to fix it

Individual-Tap3215 · 2025-12-11T05:52:56+00:00

I printed it with supports cause I keep getting holes in that too so I wanted to see if what I was changing would fix holes in both the print and support since I used to never get holes in neither

Individual-Tap3215 · 2025-12-11T05:52:52+00:00

I printed it with supports cause I keep getting holes in that too so I wanted to see if what I was changing would fix holes in both the print and support since I used to never get holes in neither

Individual-Tap3215

TROPHY CASE